Recent content by ubguessin

  1. U

    80 series axle rebuild problems

    The surface of the axle shaft appeared mint. I used some sealant on the axle seal for install. I did apply some oil to the axle shaft upon stabbing. One thing I noticed was the "oil deflector" behind the inner shaft seal was boogered up, like the actual shaft had definitely rubbed on it causing...
  2. U

    80 series axle rebuild problems

    I rebuilt my front axle and now I have a right wheel Squeaky axle and a leaking axle seal on the left hand side. I used the heavy duty axle seals and followed the service manual and I do not know what I could have done wrong.
  3. U

    G-turbo issues??

    You may be right, the only other concern is that on the last pic you can see on the intake pipe has oil seeping past as well. Even with a catch can. What adds me to thinking I am having turbo seal problems is that the exhaust has a haze to it as well.
  4. U

    G-turbo issues??

    Hello all, so recently got my 1HD-T rebuilt had it back since just before Christmas 2025. Anyways got under the truck today because I need to re-place my hub bearings and was doing some teardown. (Prolly knuckle rebuild as well). I was examining my G-turbo and noticed an oil "leak." Pics are...
  5. U

    ACSD Removal 1HD-T

    What is the likelihood of engine damage after a fresh rebuild 1000km's on the clock.
  6. U

    ACSD Removal 1HD-T

    Thanks I kinda had a feeling that was gonna be it since the plug that's in there doesn't have a hose bib and is the only one that isn't painted 🙄... now I have to figure out how to block the lower hose bib so I can actually drive.
  7. U

    Overheat warning, oil coolers RnR with complete 1HDT/ACSD complete delete

    How does the green port "go away"? I just got my truck back after a rebuild and they stuck a flimsy rubber plug on this w/ hose clamp and today it ripped open and I lost all of my coolant. 6 years ago I had my ACSD deleted but this coolant hose was still connected and functional as much as I...
  8. U

    ACSD Removal 1HD-T

    Does anyone have photos of where the hoses from the ACSD connect to the engine block? One of them is right next to the oil filter found that out today when the rubber cap the mechanic put on it after I had the motor rebuilt ripped open and lost all of my coolant. My ACSD was deleted 6 years ago...
  9. U

    location of the coolant drain plug in 1HD-T

    I just had my engine rebuilt and the builder put a rubber plug on the nipple coming out of the oil cooler where is this supposed to have a hose connected too??
  10. U

    A442F can't decide what gear it wants to be in

    Alright so finally got the new TPS after a bit of hassle with DHL. The mechanic told me he wasn't able to replace the TPS because he would have to take the intake manifold off. I told him I'll do it myself. I got the old TPS out and the new one in w/out taking the manifold off. I set the TPS...
  11. U

    Sudden downshifting with A442F and help locating transmission wiring

    I am happy to report that I was able to replace my TPS w/out having to take my intake manifold off like the mechanic told me had to be done. I am also more then ecstatic to report that the TPS has solved my erratic shifting issues. Case closed on to the next adventure!
  12. U

    Sudden downshifting with A442F and help locating transmission wiring

    What's funny before I had all this rebuilt my gauge cluster shorted out blew the fuse had to replace my speed sensor and I put in fresh wires for the speed sensor I guess I didn't know there's two speed sensors quite possibly only replace one of them I know the guy who did the swap on the motor...
  13. U

    Sudden downshifting with A442F and help locating transmission wiring

    Thank you very much for this write up and pics. I am waiting for my TPS to arrive then will definitely have to check out my wiring next. I just had a rebuilt motor and trans put in. Originaly my trans was not going into lockup. And now it's "erraticly" shifting in and out of lockup and som...
  14. U

    A442F can't decide what gear it wants to be in

    What would I need to do to check the TPS with a scope? What to hook up to and settings in scope? I took the TPS off today and hooked it up to 5v and read the voltage while sweeping the sensor. You could hardly notice a problem. I switched to reading the Resistance and this is where you could...
Back
Top Bottom