Recent content by relaxedcruiser

  1. relaxedcruiser

    Alternator “W” terminal?

    A alternator has basicly three stator windings which are all producing A/C curent. The W connection is basicly just the A/C current of one of those windings before the diode . That signal can be used for tachometers. Some alternators have the W connection ready, some don't. I have soldered...
  2. relaxedcruiser

    Help finding parasitic drain (HJ61)

    Check out the wiring plans....It could be that the fat white cable at the positive batt. terminal feeds the glow screen. I had that one and it was labelled "Glow" but my cable loom is 2H spec not 12HT so it could be different. Just take it off and check - in your - and mine climate we don't...
  3. relaxedcruiser

    Mystery 12HT injection pump piece

    I found the part number here: https://www.amayama.com/en/genuine-catalogs/epc/toyota-japan/land_cruiser/HJ61V/108175/engine/2205
  4. relaxedcruiser

    Mystery 12HT injection pump piece

    https://forum.ih8mud.com/threads/12ht-thermo-sensor.1102834/ but the real function has not yet described....
  5. relaxedcruiser

    Mystery 12HT injection pump piece

    I vaguely remember reading about it here. It is some sort of cold climate special I believe. It could be that the fuel racks movement is limited to a certain point until the engine has reached some sort of temperature - then the device is pulling back and does not limit the max fuel setting...
  6. relaxedcruiser

    Broken down on the road - fixed with Power Wagon shock bush (!) - good to know anyway.

    For some reason the pic doesn't ended up in the original post - so here is it. On the left of course the remains of the old one - the donor bush on top - and the finished replacement.
  7. relaxedcruiser

    Broken down on the road - fixed with Power Wagon shock bush (!) - good to know anyway.

    If I only had tried to pull the lever up...That's what I thought later too. But I was so puzzled that night that I didn't checked the easy things first.
  8. relaxedcruiser

    Broken down on the road - fixed with Power Wagon shock bush (!) - good to know anyway.

    To the folks with manual gearboxes and other interested people ...coming back from an exciting trip on the New Zealand south island my gear shifting got suddenly worse - hard to shift between 3rd and 4th, lever seemed to be locked in the gear it was in...s*** - what's going on here ?.... I was...
  9. relaxedcruiser

    12HT throttle shaft gasket / bushing

    Could you not track down a generic oil seal with the given measurements ?
  10. relaxedcruiser

    Flywheel step very crucial ?

    Little update here, put everything back together WITHOUT getting the step height corrected. I was literally parking in front of the engineering shop but decided not to get the step lathe machined. I did not want to risk any misalignment between the surfaces, they really need to be done in one...
  11. relaxedcruiser

    Flywheel step accuracy very crucial ?

    Tie that bar with something to the best point, probably the chassis. or use a rattle gun to get them off. But for torqueing them back up you need that setup anyway - or a second person who is holding it against the hard point.
  12. relaxedcruiser

    Flywheel step very crucial ?

    Hi Duncan, that's funny - we are doing really same stuff same time - I'm also doing rear main seal and g/box input plus the usual bearings. I'll pay the local engineering shop a visit tomorrow, I hope that he can just skim the 0.21 mm of the step - it won't be as shiny as the machining but...
  13. relaxedcruiser

    Flywheel step accuracy very crucial ?

    Shop guy is saying that I'm probably not measuring accurate enough. And he was right - but it is even worse with the dial gauge - I should have taken that with me and check on the spot - you are always wiser afterwards. I'll try a local machine shop tomorrow, they have a good lathe - and he...
  14. relaxedcruiser

    Flywheel step accuracy very crucial ?

    In my slightly tired state I used a precision straight edge and new feeler gauges to measure - and I was wrong - it is even worse. With the dial gauge it is only 0.29 mm / 0,0114 in
  15. relaxedcruiser

    Flywheel step very crucial ?

    In my slightly tired state I used a precision straight edge and new feeler gauges to measure - and I was wrong - it is even worse. With the dial gauge it is only 0.29 mm / 0,0114 in
Back
Top Bottom