Recent content by AussieFJ40

  1. AussieFJ40

    FJ40 AC wiring - plug ID needed

    Thank you Luckily the loom is unmodified and all the original connectors are present. The two connectors on the back of the control unit merge into the main AC loom, and that then splits into a Y. One branch leads to the under-dash unit and that is all correctly plugged in. The other branch...
  2. AussieFJ40

    FJ40 AC wiring - plug ID needed

    Having a good dig through. Looking at 1979 and 1981. The wiring colours do not seem to match my system perfectly - I’m seeing variations. Perhaps because I’m Australian market? I’d love to specifically know what those two plugs are supposed to be connected to.
  3. AussieFJ40

    FJ40 AC wiring - plug ID needed

    Thanks! Can you pls show the detail around the AC relay top right, and also where the BLK runs to off the control panel, lower part of the diagram.
  4. AussieFJ40

    FJ40 AC wiring - plug ID needed

    Hi all Trying to sleuth my ND AC which was dealer fitted when the truck was 3yo in 1981. Trying to ID the below bundle: -Single wire is an earth -Single blade possibly runs to pressure switch (?) -What is the 3 blade and where should it be going Many thanks!
  5. AussieFJ40

    OEM parts gurus - dimensions/pics of stock rear muffler 1978 2F

    Part No 17551-61010 FJ75 ran the same shield albeit on the centre muffler.
  6. AussieFJ40

    OEM parts gurus - dimensions/pics of stock rear muffler 1978 2F

    That’s right it does. But if you want to adapt it to an earlier truck you need the rubber cushion and small L-bracket that bolts to the chassis. Timely thread bump! I finally completed and installed the exhaust system. As part of this, I finally managed to find a correct original muffler heat...
  7. AussieFJ40

    Unobtainium

    Yes I know the light buckets offer adjustment, but I was under the impression that the glass lenses themselves had a different reflector pattern/direction for LHD and RHD, and you cant adjust that out. Any truth to that, or are all 7" Koito lights common globally?
  8. AussieFJ40

    Unobtainium

    Sorry to resurrect a very old post - but was anyone able to determine whether this kit was a LHD or RHD-market beam/spread pattern?
  9. AussieFJ40

    Toyota Jacks

    Hi mate - please note that isn't a Landcruiser jack, it's from a smaller Toyota vehicle of the period. Note the load rating is 0.7 ton, whereas all LC jacks are marked 2 ton. Great to display in the vehicle but I wouldn't use it. Cheers
  10. AussieFJ40

    Wanted NOS Denso coil p/n 90919-02015

    Sending PM now :)
  11. AussieFJ40

    Wanted NOS Denso coil p/n 90919-02015

    Hi all As per title, chasing a NOS 90919-02015, pic below for reference, many thanks!
  12. AussieFJ40

    '77 FJ40 Exhaust and Muffler

    Genuine Toyota FJ40 mufflers are still available new! Simply fit it up and have an exhaust shop join the dots between your manifold and the new muffler - easy.
  13. AussieFJ40

    '77 FJ40 - Ignition Coil replacement?

    Hi all Just to resurrect an informative coil thread: Given the internal resistor 90919-02015 is now NLA, has anyone used the 90919-02113 coil? Is this a direct substitute? FJ Company seem to use it on their builds... @beno - any advice on these parts? Cheers
  14. AussieFJ40

    OEM coil options - 1978 FJ40

    Great info thanks. So much like my original coil the 81+ is an internal resistor coil, but lower resistance. Should be totally safe if I run a ballast then?
  15. AussieFJ40

    OEM coil options - 1978 FJ40

    This was pretty well my thinking. If it’s 12v/internal resistor I should be fine. From my research the igniter module is really only needed if the dizzy calls for it - mine does not.
Back
Top Bottom