rkymtnflyfisher

Couple people make these. https://www.midnight4x4.com/products/bolt-keeper-bolt-on?srsltid=AU7gw4UWB4LJUYhWiSwPol2c-utD-9m4NpgmgIzj-OAnI1FO2wLPDdIo3Co

I'm the same as far as "skills", these things aren't that hard to disassemble and rebuild. Here's a link to their website, make sure to get your date code to order the correct rebuild kit...

Toyotas only relocated to a bigger shop on North street in Missoula. Might give them call to see if they offer that service.

Saturday night East of Eden. I remember driving through Sunny Side one early evening mid fall 2000-ish. I was weaving my way around burning couches, upturned garbage cans and blowing litter. Through the haze you could see the natives appearing...

I might know about a freshly rebuilt 2F down in the Bitterroot that might need a good home. I'll have to check if someone's wife revoked his kitchen pass or not.

there are a few guys around Missoula here on mud, also a few in the bitteroot as stated above, ATF or marvel oil in the cylinders, try rotating by hand, either by flywheel or crank pulley, if it rotates, add gas by aux can and see if it will run...

Hey everyone! I wanted to share some pictures of my new project, a 1977 Toyota Land Cruiser FJ40 with 68,000 miles on the odometer. I’m located in Montana and recently picked this one up in California. From what I can tell, it has minimal rust...

That would be Master Tech, right behind Big Dipper.

How about the shop behind Big Dipper up on the hip strip? I wonder if he has any old timers left up there that can rebuild a Toyota carb. I'm about to rebuild mine soon, if I feel froggy enough before I finish some other work up.

Too busy burning couches in Morgantown after WVU beat the TCU Horny Toads?

I didn’t make it out on the hill today….The electrician did. :bounce: Post op report indicates that I’m hard wired for the 12kw inverter. Inverter was tested (again) using petrol this time. All systems are green light go. Smooth even power...

I'm a big fan of these. What I like is that zerk fitting is protected from being sheared off. Here is how they are assembled. The pins are screwed into the plate on the zerk fitting side and the protective nuts stop the pins from rotating...

I think I'd rather go with different shackles before I start grinding metal out.

You can grind a notch in the hanger

Just test fit one. No dice, definitely isn't going to work. It might move 50%. Sure enough a recipe for disaster.

Ok guys, after another 2-week hiatus, I am back, and the FJ62 is driving, and you were all right, these overdrive gears are awesome!!! It is kinda a crazy story, but I ended up pulling the transmission again to check what was going on with my...

They are Skyjacker. Damn. I never thought about that cross piece hitting the spring perch. I'll have to test the rears out this week.

Is your springs 4" skyjacker ?

Hey John, like @bhsdriller said I do have a Delta cam I installed in the 2F rebuild I did for my 60 last year. Do you have the spec sheet Delta sent you? I'm specifically looking for the overlap degree. Is this F or 2F? I got the KC cam which...

Not that I've ever noticed.

Going out...

Well I separated the cab today , Man this restoration shop is a joke. They put the roof bolts in upside down lol , they made their own gaskets that didnt really work. Anyways found 1 spot on the interior of the tub, im gunna have to wash that...

I do realize I purchased it sight unseen and that's why I am not irate in any form , and to be honest, I am actually thrilled to have a project like this, truly. I just think that people should know this is what is considered fully restored...

Thats who I got it from, more than 2 years later. I guess I will spill the beans on this whole deal. Supposedly, the car was sold and the new owner disappeared. Motoriot out of Kent got the paperwork back and reposted the truck at a very...

Nothing too exciting on Scout, I changed the transmission fluid in the newly rebuilt transmission as it's been about 200 miles since Torfab did their magic. I used just under a gallon of 85w90 GL4. Took it for a spin and noticed that the 1st...