40, 60, 70, 80, & 200 Series Cup Holders (1 Viewer)
- Thread starter bhicks
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Can we get some picks of one mounted in an early 60?
- Thread starter
- #303
I only have the pics from my fitment console. It's not in the vehicle but you can at least see how it sits on the console. I will get pics of it installed in a 60 soon.
Thank you!
- Thread starter
- #305
The 60/62 Rear Cup Holder is now available on my site and my etsy page. Here's the links:
60/62 Series Rear Double Cup Holder - BH3D Printing
Etsy Link: 60/62 Series Rear Double Cup Holder
60/62 Series Rear Double Cup Holder - BH3D Printing
Etsy Link: 60/62 Series Rear Double Cup Holder
I will post pics of the one I ordered when it gets here, figure someone has to be the first!
Ordered a front console one before I saw these pictures. I wasn’t sure it would work with seat up but pics show it does. Very excited about this product.
Have you though of making a silicon liner for them? I was looking at mine for the front position in the 60 and since I don't want to screw in, it has two holes which liquids can leak into. I currently have some shop towels in the bottom to absorb any leaks.
- Thread starter
- #310
Your the first person to ask about that. I have not thought about silicone/ruber liners but it's definitely something I can look into. I figured 99% of cup holders on the market are simply plastic holes molded into the body of the console. Rarely have I seen drain holes or silicone inserts in OEM cup holders. I could probably print some rubber inserts that would look more like a coaster that would match the bottom diameter of the cup holder that could be easily removed and washed. The down side is that the flexible "rubber" filament on the market has a very low melting point and would not be dishwasher safe. You got the gears turning now. I will look into this further when I have some down time.
- Thread starter
- #312
I finally wrapped up the center console ashtray for the 81-84 40 series. It took a while to get the design wrapped up. The OEM design had some serious structural issues leaving it very prone to cracking. The hardware was also sub par. I needed a design that looked, fit, and functioned like the OEM but had all the needed improvements. I don't know if this will be a big seller or a flop. I made a medium sized batch of the ashtray and the cup holder that goes into the ashtray hole. If they do sell well, I will make another batch asap and restock as quickly as I can. I apologize for the ashtray being so expensive. $45 was as low as I could go. There is a ton of supports to make this part look correct. There is also a ton of hand sanding and acetone smoothing to make it look correct. The labor just killed me. The cup holder insert has way less support, way less labor, and doesn't require any assembly so I was able to keep it's price lower. PLEASE be aware that my ashtray will NOT come with the metal spring plate. It's not really needed with my hinge design but I went ahead and left the slot for it in case folks want to reuse the OEM one from their cracked ashtray.
Here's a link to the product page:
40/45 Series Landcruiser Archives - BH3D Printing
Here's the links to my etsy pages for folks that need it shipped outside the US.
Ashtray 40 Series Landcruiser 1981-1984
Cup Holder Ashtray Insert 40 Series 81-84
Here's a link to the product page:
40/45 Series Landcruiser Archives - BH3D Printing
Here's the links to my etsy pages for folks that need it shipped outside the US.
Ashtray 40 Series Landcruiser 1981-1984
Cup Holder Ashtray Insert 40 Series 81-84
- Thread starter
- #314
So the next product for the 80 series is about to be released. This is for the dash of the 91-94 80. I made the cell phone mount/dash bezel for the 95-97 but never built a phone mount for the 91-94 until now. This will be available on my website by the end of this week. I will post a link to the product page here once it's available. Here's some pics of how it turned out.
Super cool! What kind of attachment does it support? I currently use a magnet to secure my phone to the dash.
- Thread starter
- #317
Right now it just supports the phone mount pictured. I may design a ram mount version and magnet mount version in the future.
Any plans on having a Memorial Day sale? Thanks
- Thread starter
- #319
No BUT I'm still offering the mud member discount. Use coupon code "TEQ15" during checkout. That will give you 15% off the entire order and still allow for free shipping anywhere in the US.
Good enough, I’ll place my order. Thanks
