BadReligion

My office is textured, ceiling painted, LED lights in, and the walls being painted: The master closet is textured, painted, and LED lights in. This room just needs flooring, baseboards, door and trim to be finished: Master bedroom is...

Usually it's the o rings going into the rear evaporator that fail. Or the hard lines on high mileage and salt exposed vehicles. Hope they used Nylog Blue on the new ones. $1000 for a rear evaporator replacement is very fair, it's an 8 hour job...

You do not need to remove the steering wheel. That alone disqualifies your mechanic. It's not a difficult repair.

On the road! Well posting this from McGill, NV but this was us 7 hours ago. Lehmans Caves tomorrow morning, then on to Moab!

I suggest this spot in that area. Camped there last year before CM: 39.13876, -109.02661. and give yourself enough time to hit Colorado National Monument as well. Had to do one last meeting at camp before shutting down for the week. Best...

Truck is loaded as of last night. Gassed up today, finished packing a few things. Picking up a friend of mine tomorrow morning and planning to be in Grand Junction Sunday evening to camp around Rabbit Valley as that’s where the Kokopelli run...

That's what I thought too!

I’m bringing a trailer with me because I don’t want to go deaf riding 37s from Florida, so I’ve got space. Just swapped from ARB skids to budbuilt ones - if anybody wants/knows someone who could use the ARBs, I’ll bring them and they’re yours for...

Hidden swing out frame mount. 1/4” plate and 3/16 wall tube.

Not terrible. It just takes a lot of time and beats up your hands. The first wheel took me like 3 hours, then maybe 1.5 hours each for the other 4. Definitely a full day project. Get a proper set of tire irons to make life easier. Coyote has a...

Shipped her out west for Cruise Moab

Thanks. 3/4 inch plywood held up by 3/4 inch steel pipe. It is split so that the second row can be used. The front part can rest on top of the back part when using the second row. The two parts bolt together easily when needed and bolt...

Resurrecting an old thread. Giving them a try on my 80. Bias ply Maxxis Trepadors keep burping air and blowing the inner bead, even with an outer external beadlock. I have to air them down to 8-10 psi to get the sidewalls to flex because they are...

Moab Prep. Installed some pneumatic inner beadlocks. Even with external beadlocks, I was still having issues burping air or full on blowing the inner bead on these bias ply Maxxis Trepadors. They have a really stiff sidewall so you have to air...

Installed some new-to-me door cards all around. New window regulators/motors from Cruiser Outfitters, added some sound deadening to the inside of the doors, new vapor barriers, new window seals along the inside of the door panels, and some One...

Yesssss…… Getting rig prepped. LC skillsets transfer over well to bike packing. 👍👍

Fired up the sawmill and cut lumber and built a “land bridge” so the residents could get to work, school, shopping, etc.

Once the water went down to a reasonable level, rebuilt the bridge. Added an additional 48” x 40’ culvert tube next to the existing one.

Added some stabilization to the down stream side of the dual 48” culvert tubes.

If someone is buying based on interior space, then a Sequia would be the way to go. Yes, the 3UR has the edge on HP, but the flat torque curve on the TT6 and 10 speed transmission make it feel quite a bit faster. I've only driven the LX600, but...

Saying a 3-4 year old 200 with a minimum of 20k mi put on by someone else and just out of the factory warranty is better than a new GX550 that tows more, has more HP and Torque, slightly better mileage, 10 year newer infotainment system and...

I think it looks good and is an efficient use of a small space, but as others have said, definitely make at least one side (non window side) wider to accommodate storage, cabinets, and working space. Even space for the lift column on that side...

Well, we didn't get started on texturing yet; got side tracked finding all the sewer and drain lines that come out of the house (there are four separate ones total). Had to do some trenching by hand to find them, since they come out under the...

Joe Hauler or Versahaul. These are a bit more expensive, but use a tensioned wedge at the receiver to reduce wobble. Cheaper carriers are also bolted together, not welded, and wobble a lot. You can make a cheap carrier stable with a little...

Sounds like Hell's Revenge on Thursday will be an almost total 200 takeover, I think I got the last spot. Wipeout Hill on Friday. I'm thinking Porcupine Rim on Saturday but I could be convinced to do something else.