Wobble when breaking hard

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 5, 2015
Threads
9
Messages
26
Hey guys, I need some help diagnosing a problem. Im on a little weekend trip up in North GA. Going up and down a mountain road last night my front end began to wobble when breaking hard. This is the first time that I have experienced this issue since I have owned the vehicle (little over a year). I did not experience any issues on a 4 hour drive up 75 and through Atlanta. I was on the same road back this past summer with no breaking issues. I did replace the break pads about 3 weeks ago with Toyota pads.
I did a search of the forum and found a few nuggets of info. Some said to get new calipers. Some said that the wheel bearing nut is loose. I do have a tiny bit of play when I shake the wheel in a 12/6 motion.
Any expert advice would be much appreciated. My Cruiser is a 97 with OME lift and 33's.

Thanks!
 
Hey guys, I need some help diagnosing a problem. Im on a little weekend trip up in North GA. Going up and down a mountain road last night my front end began to wobble when breaking hard. This is the first time that I have experienced this issue since I have owned the vehicle (little over a year). I did not experience any issues on a 4 hour drive up 75 and through Atlanta. I was on the same road back this past summer with no breaking issues. I did replace the break pads about 3 weeks ago with Toyota pads.
I did a search of the forum and found a few nuggets of info. Some said to get new calipers. Some said that the wheel bearing nut is loose. I do have a tiny bit of play when I shake the wheel in a 12/6 motion.
Any expert advice would be much appreciated. My Cruiser is a 97 with OME lift and 33's.

Thanks!

My guess is wheel bearings. I don't know enough about ABS, but that could be involved too. Wheel bearings ain't no joke if you let them go long enough. At best, I'd think you should pull the hub open and inspect and retighten what you have. Assuming it is the bearings, worst case is having to buy new bearings and races (and the install kit if I remember right). You'll have to have the whole hub apart.
There's some good threads on here about how to do it. You'll need someone to press the old races out and new ones in if you don't have a bearing press, and the hub tool. You ought to be able to rent one from AutoZone or similar.


That's all assuming it's the wheel bearings, but that's my gut feeling
 
You don't need a press
1 pound out old race and keep it
2 set new race in and start with rubber mallet
3 place old race on top of new race and pound in new race , you can use reg hammer since you are hitting the old race
4 smack till you have it seated this will also seat the old race just smacked it back out by its lip
5 drink beer repeat for other side
Be sure hub is very clean and free of any burs or dirt so race seats fully
 
Mine were in real tight and I don't have the fancy Harbor Freight kit either haha. Should be 54mm. It's NOT the one for manual locking hubs- the 4point, keyed, round socket. It's a 6 point
 
i would also vote the hub nut is loose. where are you located now? where are you from? 4 hours on I75 should put you near my part of the world. i have a 54mm hub nut and all the tools you could need to do anything on the front end and wouldnt mind helping.
 
You don't need a press
1 pound out old race and keep it
2 set new race in and start with rubber mallet
3 place old race on top of new race and pound in new race , you can use reg hammer since you are hitting the old race
4 smack till you have it seated this will also seat the old race just smacked it back out by its lip
5 drink beer repeat for other side
Be sure hub is very clean and free of any burs or dirt so race seats fully


Beer is always #6 on this forum. Find something else for #5.
 
Hey guys, I need some help diagnosing a problem. Im on a little weekend trip up in North GA. Going up and down a mountain road last night my front end began to wobble when breaking hard. This is the first time that I have experienced this issue since I have owned the vehicle (little over a year). I did not experience any issues on a 4 hour drive up 75 and through Atlanta. I was on the same road back this past summer with no breaking issues. I did replace the break pads about 3 weeks ago with Toyota pads.
I did a search of the forum and found a few nuggets of info. Some said to get new calipers. Some said that the wheel bearing nut is loose. I do have a tiny bit of play when I shake the wheel in a 12/6 motion.
Any expert advice would be much appreciated. My Cruiser is a 97 with OME lift and 33's.

Thanks!
I had a similar problem with my 97 landcruiser. Smooth as silk while driving around and on the flat. Braking hard on downhill caused serious side to side wobble. chased it for over a year. Tightened/re-packed wheel bearings.. a little change. Replaced the steering damper shock and rod ends..a little change. Finally replaced front disks ( kept old calipers). solved the problem entirely. Disks/pads did not show signs of warpage in wear .. but they were old and worn enough they were clearly worn too thin to be turned so I just replaced them and didnt get any numbers on how warped they were, but there was immediate and complete relief from the wobble
 
If you were going up and down and braking hard, you could have uneven deposits on the rotors, will cause the same symptoms. This link below has worked for me in the past multiple times. Changing pads could be a lot easier than other work, worth a shot.

Uneven Pad Deposit Removal
 
After reading your first post my first question is did you just do a brake pad slap or did you install new rotors as well? If you did a slap then your ssue isn't too serious; just uneven wear on the rotors as stated above by Izzyandsue. When you put new pads on older rotors without turning or replace them it is common to get a wobble or pulsation when breaking, compounded under severe conditions. I've gotten use to mine, no worries though, will install new rotors next time around.

Just my $0.02.
 
Back
Top Bottom