Windshield washer not working

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 23, 2012
Threads
116
Messages
1,064
Location
Everett, Wa
I've searched on this one and cannot find anything. I cannot get the sprayer on my 1978 FJ40 to work. I've gone through the following troubleshooting, but I must have overlooked something:

  • Switch works for the wipers, though I think my wiper motor isn't working great, there is only one speed.
  • Wiper fluid pump motor is new, I just replaced it. Replaced the fluid too
  • Fuse works since the wipers work.
  • Wiring connectors are in good shape, but it looks PO replaced them with standard spade connectors. Not sure what the factory connector looks like.
  • Opened up the house to look for blockage and none that I can find
Alright, that is where I am right now. Looking for other options. Would taking the switch out and testing all the internal connections be the next move?
 
I just replaced the connector on my '77 this weekend with the MF 2P6.3B connector from Mark (coolerman). I did clip off the catch for looks but it fit perfectly

Cruiser Wiring

washer pump clip.webp
 
Good to know. I've got some connectors from him in the past. I should have thought to look there. Thanks!
 
Does the new pump motor run?

The switch has a crappy ground mechanism to power the pump motor. If it's not too oxidized, you can sometimes turn it all the way to the stop and wiggle it to help clean the contact surface. Worst case, pull the switch and clean the washer contact mechanism at the very front of the switch.

Does the wiper motor run in both speed positions or just one of the switch positions?
 
The new motor should work, I will test it when I get home. Good to know on the switch, I will try that too for the cleaning.

The wiper motor works on both settings, there is just no difference in the speed between the two positions.
 
I just borrowed this photo from an earlier thread. That brass arm and the zinc-plated rotating part to the left of it in the photo are the washer motor contacts. The zinc-plated part rotates with the switch shaft and contacts the brass arm to provide ground for the pump motor. Often, they are oxidized and need cleaning.

upload_2015-9-8_13-28-8.webp


I think it's odd that the wiper motor would run in both positions, but at the same speed. Are you running it on a dry windshield? Even though the 78 motors are stronger than the earlier versions, they still don't run well on a dry windshield. See if you get a difference in speed with a wet windshield.
 
My son made the comment on his '77 wipers that they have 2 speeds...... slow ...and not quite as slow. Very little difference.
 
My son made the comment on his '77 wipers that they have 2 speeds...... slow ...and not quite as slow. Very little difference.

With new brushes, lube, and a good armature, you'll have fast, and stupid fast.

Sounds like your motor needs some TLC.
 
Just as a follow up to this in case anyone looks it up in the future, Spotcrusier's tip worked. I just played with the switch, making sure to rotate the switch enough to try and clean off the contacts and low and behold after a few tries it worked. Thanks again everyone!
 
Also note the White black wire. It's a ground for the system. Where it connects to the switch body can corrode and where the front of the switch contacts the dash.
 
I realize this is an old-ish thread at this point, but I have a pertinent question for diagnosing why my washer motor isn't working:

If I'm reading the wiring diagram right, the switch for the washers provides ground to the circuit (as opposed to connecting a 12v source). Would it be fair to say that if I put a meter between the wire that connects to the pump and the chassis that it should read 12v at all times?
 
Back
Top Bottom