What tools do I need?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 7, 2007
Threads
7
Messages
84
Hello from south Houston,

I've got a 97 fjz80 that I'm going to be replacing a head gasket. I've read through the FAQ's, and am pretty confident I'll be able to get it done over the next two weekends. I've tried to PM Idaho Doug about getting his DVD but with no success. I was just wondering what speacial tools i'm going to need to get the job done. I already have a decent set of sockets with extensions, air rachets (w/compressor), a torque wrench, FSM, and an engine hoist. Is there any thing out of the ordinary I will need? Also, is there anyone in my area who has a copy of the video I could borrow before this weekend?

I was also looking into pm'ing the alternator, starter, and fuel injectors. Ohh, one more thing, what's the best way to locate the PHH. I don't know which hose it is, since alot of them are "pesky"

I appreciate all the info. and help. This forum kicks a**:flipoff2:
 
Dude...my Dad has an awesome set of tools...we can fix it.

spicoli.jpg











Seriously though...you will need a LOT of tools.
 
Off the top of my head (pun intended)...:D

-30mm 6-point socket for crankshaft bolt to get to crank shaft seal (might as well do it while you are in there)

-a good assortment of 6-point metric sockets--both deep sockets and regular. You will use the 12mm, 13mm, and 14mm sockets a lot.

-metric wrenches (the gear ratchet style has helped immeasurably)

-a long breaker bar (preferably 1/2" and abot 2' long)

-BFH :eek:

-phillips screw driver

-feeler gauge if you are going to check valves after you have put the sucker back together again.

-timing light for setting timing (or advancing depending on where you live)

-3/8" ratchet/1/2" ratchet/1/4" ratchet

-at least 3 6" extensions

-at least 2 universal adaptors.

-torque wrench that is properly calibrated

-scraper to get gasket remains off of head/block.

-some vice grips, snips, various sized pliers, needle nose plier, needle nose plier that bends (has an "L" shape to it.

-crescent wrench (good sized one) to use on the cams as well as the EGR union nut.

-magnetic, telescoping grabber (I always drop nuts and bolts).

Hmmm....that's all I can come up with right now.

Good luck.
-onur

Oh shoot, I forgot: 1 12point, 12mm socket, and one 12point, 13mm socket.

:)

-
 
Last edited:
beno, are you sure thats it?

Nope. :p

-I forgot to add a 5/8" spark plug socket.

-intake cleaner/carb cleaner

-wire brushes, brass bristled brushes.

-locktite 242

-anti-seize

-some cheap motor oil

-dielectric grease

-the socket-ended universals are nice to have too--preferably 6-point, 12mm and 13mm.

There are a bunch of other tools that I haven't added to this list because the OP did not say if they were doing anything beyond just the HG. I did go beyond it, so there are more tools not included here.

-o-
 
Thanks for the input Beno, I'll try and score those before Saturday. I was able to get a hold of Idaho Doug, and hopefully I'll be getting the video in also. Any takers on telling me which hose is the PHH???
 
Thanks for the input Beno, I'll try and score those before Saturday. I was able to get a hold of Idaho Doug, and hopefully I'll be getting the video in also. Any takers on telling me which hose is the PHH???


It would take longer for us to tell you than it would for you do a search on it.

Not trying to be ugly, just saying...there is lots written up on it (and pics. as well).

Good luck with your HG. Let us know how it goes.
 
Nope. :p

-I forgot to add a 5/8" spark plug socket.

-intake cleaner/carb cleaner

-wire brushes, brass bristled brushes.

-locktite 242

-anti-seize

-some cheap motor oil

-dielectric grease

-the socket-ended universals are nice to have too--preferably 6-point, 12mm and 13mm.

There are a bunch of other tools that I haven't added to this list because the OP did not say if they were doing anything beyond just the HG. I did go beyond it, so there are more tools not included here.

-o-

And a BF wrench, 30 or 32mm for the EGR and a good step ladder. You will also need your full collection of swear words, you will use them all. :bang::bang:
 
Might be easier to pull the engine if you have the equipment, that way you can do the oil pan seal and rear main... I have this Porsche 951 and in hindsight I should have pulled the engine as it would have made things ALOT easier. (clutch, front rear seals, head gasket, balance shaft housings and if the oil pan gasket leaks I then have to drop the front suspension....)
 
Might be easier to pull the engine if you have the equipment, that way you can do the oil pan seal and rear main... I have this Porsche 951 and in hindsight I should have pulled the engine as it would have made things ALOT easier. (clutch, front rear seals, head gasket, balance shaft housings and if the oil pan gasket leaks I then have to drop the front suspension....)
I was thinking about it since my rear main is leaking. Once I get the head off, I'll see how much more work its going to be.
 
Any takers on telling me which hose is the PHH???


The PHH is located on the driver's side of the head, all the way to the back. It is a small metal pipe coming out of the bottom side of the head, to a small hose, which then goes to a metal pipe heading up to the heater valve over the head on the firewall.

Good luck.
-onur
 
And be very careful of the plastic nipple on the top of the Radiator, leaning on it can break it and then you will need a new Radiator
 
Get a TSM - its invaluable. Some of the steps in it can be skipped, or modified to reduce the amout of work, i.e., stringing the harness through the intake mani, and leaving the exhaust mani on the down tube. I would also get a 10mm and 12mm ratchet wrench. These are not necesary, but save lots of time. Also, get some heat wrap to wrap up your wire harness by the egr tube. I used a wire brush bit and my cordless drill to clean carbon off my pistons. Also get some duct tape and a marker for labelling harnesses and a bunch of zip lock bags to keep track of nuts and bolts. I would also by a few extra hose clamps.

Karl
 
And be very careful of the plastic nipple on the top of the Radiator, leaning on it can break it and then you will need a new Radiator

Thanks for all the reply's. I actually took the radiator out so that I would have more standing room on the frame and front cross member. I broke the nipple that you are referring to already while changing out the water pump, on a previous PM and have already had to replace the radiator. Alot of $$$ for a little broken off piece of plastic. :hillbilly:
 
You will need a set of internal torx as well to take off the exhaust manifold studs and to remove the EGR pipe to intake manifold studs. you will need a big wrench to remove the egr nut(take a look, I use Kipnex plyiers a square jaw adjustable plyier). I have never needed a 13mm on a Toyota truck from Japan(only on the running boards which is added here in the US). If you need to do the the pan and front timeing cover then pulling the engine may be easier in the long run. Good luck robbie
 
Back
Top Bottom