What have you done to your 100 Series this week?

[phippsj]

Removed the ugly faded pinstripes with a 3M rubber wheel. Very nice! A great success!

 

[rvrats2]

Took a drive. Express creek to Taylor pass isn't quite open but we pushed some snow around. Failed on the 100 60 40 picture. Watch out for moose. Had one walk 100ft from camp on express creek road, CO.
Hey look a bear, oh shhh a moose!!
Love my backyard.

 

[OregonLC]

Took a drive. Express creek to Taylor pass isn't quite open but we pushed some snow around. Failed on the 100 60 40 picture. Watch out for moose. Had one walk 100ft from camp on express creek road, CO.
Hey look a bear, oh shhh a moose!!
Love my backyard.

Lol. Leaving for a 5 day expo on Tues. Be up as high as 6k, hopefully we don't encounter drifts such as that, although there are a few north facing cuts.

 

[Muddy Bean]

Black outside matches perfectly all the time

Lol. True story

Sent from my iPhone. Clumsy fingers may contribute to mistakes.

 

[onpoint01]

Took mine for a Boat Ride across Lake Michigan!!

Had a nice 4hr boat ride from Michigan to Wisconsin.

 

[LTrain0800]

Post a picture of the results! Sounds like a great idea...

 

[Supra88]

Debadged the hundy.

 

[DeltaT]

New pads and rotors in the back. They were pretty much toast. Big difference.

 

[TeCKis300]

replaced my low beams with some Phillips 55W Visions.. what an improvement!!!

Which visions did you get? X-Treme, Visionplus, or Crystal?

I assume you got a full set for low, highs, and fogs? They look great!

 

[twentyocho]

Which visions did you get? X-Treme, Visionplus, or Crystal?

I assume you got a full set for low, highs, and fogs? They look great!

Vision plus

 

[1loudLX]

Just got done doing the first panel.... what do you think? Took longer than expected, not looking forward to doing the rest of the vehicle lol

I could be a fan, make sure to post pics as you go. Let me know how the cladding works out for you. I want to matte wrap the white LX with white film but not sure if the cladding would be too much work.

 

[Tuffcruiser]

Installed a Traction control off switch....

http://img.photobucket.com/albums/v625/tuffcruiser/wattos038800x533.jpg

http://img.photobucket.com/albums/v625/tuffcruiser/1386282a-ea98-4773-9a79-a7d13193df43.jpg

 

[Supra88]

Installed MT sliders:

 

[re_guderian]

put 1500 miles on it from Sat-Sun... Phx-SLC-Phx with a few side trips.

 

[Wilsil]

Refurbished the front sway bar.
I was hoping that the body roll was reduced or even gone.
But no.
What can it be?
Torsion bars?

 

[Larco1001]

Debadged the hundy.

I debagded, painted matte black and re-badged...of course I rearranged a few and left off a couple. (Badging was "gold" package,,,yuk!)



Sent from my iPhone using IH8MUD

 

[Tuffcruiser]

Installed a Traction control off switch....

http://img.photobucket.com/albums/v625/tuffcruiser/wattos038800x533.jpghttp://img.photobucket.com/albums/v625/tuffcruiser/wattos038800x533.jpg

http://img.photobucket.com/albums/v625/tuffcruiser/1386282a-ea98-4773-9a79-a7d13193df43.jpghttp://img.photobucket.com/albums/v625/tuffcruiser/1386282a-ea98-4773-9a79-a7d13193df43.jpg

My bad I should have said Atrac off switch.

 

[crawfs00]

day trip west of Monument Co

Got a few poser shots and gave the A-Trac a good work out.

 

[FlammableFishie]

Got a new steering rack and two new CV axles put in

 

[Supra88]

Installed MT sliders:

A few have asked how I handled the brake lines when installing the sliders. I wrapped the u bolts with cut 1/4 fuel line as a barrier between the slider and brake lines.