Welding rear diff gears on 81

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Bring it.... just stand by when I commence to tearing you down.......♠

Welding diffs on a land cruiser is straight ghetto. Unless its going to be a chopped buggy that you bash the ever living piss out of its a terrible idea. If you want to weld diffs you should go buy and XJ and do it to that.

There is nothing wrong with an aussie locker on the 80 though. The loading unloading is mainly felt in 2wd rigs and thats amplified if it a manual. You have to have constant throttle or be off the throttle entirely when going into a corner or it will bind and buck.

But our 80's are automatics and full time 4wd so you don't need to worry about that. You can run a aussie locker in the front but you need to have the rig converted to a part time 4wd. Personally it would drive me NUTS if I didn't have the ability to selectably unlock and lock the front but different strokes for different folks.

Bottom line, forget welding the diff you will hate it, eventually selling it to someone else who end up wondering "wtf is this s***?"
 
Last edited:
Welding diffs on a land cruiser is straight ghetto. Unless its going to be a chopped buggy that you bash the ever living piss out of its a terrible idea. If you want to weld diffs you should go buy and XJ and do it to that.

There is nothing wrong with an aussie locker on the 80 though. The loading unloading is mainly felt in 2wd rigs and thats amplified if it a manual. You have to have constant throttle or be off the throttle entirely when going into a corner or it will bind and buck.

But our 80's are automatics and full time 4wd so you don't need to worry about that. You can run a aussie locker in the front but you need to have the rig converted to a part time 4wd. Personally it would drive me NUTS if I didn't have the ability to selectably unlock and lock the front but different strokes for different folks.

Bottom line, forget welding the diff you will hate it end up selling it to someone else who ends up wondering "wtf is this s***?"

And I'm sure with a name like smokingrocks you know all about the ghetto.... right chief?
 
A spool or Lincoln locker on a street vehicle is a bad idea. The tire wear alone is reason enough not to do it.

I believe I'm ordering lunchbox Aussie in about 2 minutes. I appreciate the opinions. Not really concerned with tire wear..... I have a warehouse full of 35's, it's just the loading and unloading that I was curious about. But from the sounds of it, the 80 is fine with the Aussie, where my old Heeps would get thrown into the ditch with one! Thanks again!
 
Don't make fun of the whisky tangos or the squids.

"BEST TAXI CAB SERVICE IN THE WORLD"! They always delivered us into combat right on time to whip some ass!☠♠
 
Darn straight, go pop your head in my build thread.

Do it once, do it right. I'm 97% sure that I have finally removed all of the PO's janky ass bullspit.
 
Darn straight, go pop your head in my build thread.

Do it once, do it right. I'm 97% sure that I have finally removed all of the PO's janky ass bullspit.

I checked out your build..... not bad at all! Be careful though..... the next owner is going to talk s*** about you too! Lol
Like.... why the hell did the PO decide to drill thru his roof and silicone the holes?! Now, nothing personal here, but THAT is what I call ghetto! Anyone can buy parts and bolt them on, but is it really ghetto if someone wants to try to build it themselves first? Watch out for Karma..... it's a bitch! Peace out!
 
It's just the loading and unloading that I was curious about.

Don't worry about it. They don't load and unload. They automatically drive one wheel or the other or both in the case when one wheel is slipping. The rules are simple:. No wheel can turn slower than the ring gear in either direction. One wheel can turn faster.

They swap drive sides when you go from accelerate to coast and coast to accelerate and when you turn L to R or R to L. They can make popping and banging noises when they need to swap drive sides when the other side is in the middle of its ratcheting cycle, but all of this is normal and the noise doesn't matter. You can minimize the noise by not accelerating while you are in a turn. Accelerate after you finish the turn and you won't notice them.
 
I checked out your build..... not bad at all! Be careful though..... the next owner is going to talk s*** about you too! Lol
Like.... why the hell did the PO decide to drill thru his roof and silicone the holes?! Now, nothing personal here, but THAT is what I call ghetto! Anyone can buy parts and bolt them on, but is it really ghetto if someone wants to try to build it themselves first? Watch out for Karma..... it's a bitch! Peace out!

I see you took my post personally...

If you saw my rig in person the notion of 'ghetto rigged' wouldn't even cross your mind. And if you read the thread you'd realize that the PO was the master of the silicone. :slap:

Next owner? Ha! I'll be buried in my 80. And yes it is ghetto to weld your diff.
 
Last edited:
They can make popping and banging noises when they need to swap drive sides when the other side is in the middle of its ratcheting cycle, but all of this is normal and the noise doesn't matter. You can minimize the noise by not accelerating while you are in a turn. Accelerate after you finish the turn and you won't notice them.

This is the most noticeable thing about lunch box lockers. You can add Really thick gear oil to help quiet it down.
 
I see you took my post personally...

If you saw my rig in person the notion of 'ghetto rigged' wouldn't even cross your mind. And if you read the thread you'd realize that the PO was the master of the silicone. :slap:

Next owner? Ha! I'll be buried in my 80. And yes it is ghetto to weld your diff.

Ok hot rod! So it's cool for you to silicone up your led's, but somebody else trying to fab something themselves is ghetto? Uh hu.... when you grow out of the milk mustaches, and rides on your daddy's knee.... give me a holler! $ for $ I'd bury your young butt!
 
You realize this is the internet right. :clap: And I did warn you that you wouldn't like my opinion but you asked for it so here it is in large bold text.

WELDING YOUR DIFF IS GHETTO :moon:
Tell me where in that statement I say that fabricating things yourself is ghetto?

Actually you know its a fantastic idea, you should weld your rear, center and front diffs then you'll be cool like all the 3x locked 80's.
 
Bro you are getting way to worked up over this to the point that you aren't even understanding my post.
Ok hot rod! So it's cool for you to silicone up your led's, but somebody else trying to fab something themselves is ghetto? Uh hu.... when you grow out of the milk mustaches, and rides on your daddy's knee.... give me a holler! $ for $ I'd bury your young butt!

no I quite clearly pointed out the previous owner made that fabtabulous silicone mess. Here I'll point it out to you.

I see you took my post personally...

If you saw my rig in person the notion of 'ghetto rigged' wouldn't even cross your mind. And if you read the thread you'd realize that the PO was the master of the silicone. :slap:

Next owner? Ha! I'll be buried in my 80. And yes it is ghetto to weld your diff.

Just relax, if you want to weld it then do it up. You came here for opinions if you don't want to listen to them then whatever. Do you.
 
Bro you are getting way to worked up over this to the point that you aren't even understanding my post.


no I quite clearly pointed out the previous owner made that fabtabulous silicone mess. Here I'll point it out to you.



Just relax, if you want to weld it then do it up. You came here for opinions if you don't want to listen to them then whatever. Do you.
 
You realize this is the internet right. :clap: And I did warn you that you wouldn't like my opinion but you asked for it so here it is in large bold text.

WELDING YOUR DIFF IS GHETTO :moon:
Tell me where in that statement I say that fabricating things yourself is ghetto?

Actually you know its a fantastic idea, you should weld your rear, center and front diffs then you'll be cool like all the 3x locked 80's.

Dang good idea!
 
Lol... I'm not getting worked up, but I am getting you frazzled. Lol..... I do appreciate your opinion, believe it or not. I told you... your not going to hurt my feelings.....I promise.
I must of misunderstood you, I thought you said you ran a carriage bolt thru your roof to secure your China lights, then siliconed the holes. My bust, I didn't catch it was the prior owner.
I have no problem spending the cash to buy parts, and I see your the same. But, I was taking offense when you were bagging on (I thought) people that enjoy fabbing up parts. And, in my opinion, welding up a rear diff isn't ghetto.
Anyways, enjoy your ride! I'll be in Moab around Easter.... look me up.... I would ENJOY it.☠
 
Don't make fun of the whisky tangos or the squids.

From the urban dictionary:
"Squid
A young motorcyclist who overestimates his abilities, boasts of his riding skills when in reality he has none. Squid bikes are usually decorated with chrome and various anodized bits. Rear tyres are too wide for their own good, swingarm extended. Really slow in the corners, and sudden bursts of acceleration when a straight appears. Squids wear no protection, deeming themselves invincible. This fact compounds intself with the fact that they engage in 'extreem riding'--performing wheelies and stoppies in public areas. Squids wreck alot. Derived from 'squirly kid'"

Thinkin' @pinhead was referring to the squid mentioned above aka hack, half arse, or etc. It's just like a Jarhead Infantryman to believe every discussion is somehow revolving around our beloved Corps :flipoff2:

Relating to your original post- having run welded and lunch box hands down lunch box..I had a friend with a detroit locker and 36 swampers on a truck chassis. It would unload pretty violently and when wet the combo of light rear end, slick swampers, and wet road, was sketchy. I don't think a mech locker would apply the same level of sketch on an 80 chassis.

On my truck, the welded was predictable as you mentioned before, but the mech locker was much more civil. When making turns on dry pavement you could feel the drive train binding and it would wear down the tires something fierce. Unfortunately I don't have any 80 real world experience to contribute but I think the truck chassis high lites the extremes of both choices:beer:
 
You realize this is the internet right. :clap: And I did warn you that you wouldn't like my opinion but you asked for it so here it is in large bold text.

WELDING YOUR DIFF IS GHETTO :moon:
Tell me where in that statement I say that fabricating things yourself is ghetto?

Actually you know its a fantastic idea, you should weld your rear, center and front diffs then you'll be cool like all the 3x locked 80's.

I wonder how the cdl switch would effect this?! Hmmnn... I'll give it a shot! Where's the Lincoln?! Lol
 
From the urban dictionary:
"Squid
A young motorcyclist who overestimates his abilities, boasts of his riding skills when in reality he has none. Squid bikes are usually decorated with chrome and various anodized bits. Rear tyres are too wide for their own good, swingarm extended. Really slow in the corners, and sudden bursts of acceleration when a straight appears. Squids wear no protection, deeming themselves invincible. This fact compounds intself with the fact that they engage in 'extreem riding'--performing wheelies and stoppies in public areas. Squids wreck alot. Derived from 'squirly kid'"

Thinkin' @pinhead was referring to the squid mentioned above aka hack, half arse, or etc. It's just like a Jarhead Infantryman to believe every discussion is somehow revolving around our beloved Corps :flipoff2:

Relating to your original post- having run welded and lunch box hands down lunch box..I had a friend with a detroit locker and 36 swampers on a truck chassis. It would unload pretty violently and when wet the combo of light rear end, slick swampers, and wet road, was sketchy. I don't think a mech locker would apply the same level of sketch on an 80 chassis.

On my truck, the welded was predictable as you mentioned before, but the mech locker was much more civil. When making turns on dry pavement you could feel the drive train binding and it would wear down the tires something fierce. Unfortunately I don't have any 80 real world experience to contribute but I think the truck chassis high lites the extremes of both choices:beer:

Lol...... your probably right! I hear "squid" and I think TAXI! Lol.... I guess 21 years riding the worlds best taxi cabs have brain washed me!
On the post.... That is what I've heard, but between opinions here....... I have ordered a Aussie tonight!
I'm just hoping the 80's don't get the violent "un-locking" like you mentioned in the rain, and on the highway. Tires don't worry me.... I know enough SNCOIC's aboard Lejuene to keep me in 35's for life.
Between Tools R Us, Mudder, and Pin Head's remarks I think lunchbox is safe. Between the 3 of them, they HAVE A LOT of experience.
I appreciate everyone's opinion though!
 
Back
Top Bottom