Welding rear diff gears on 81

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 22, 2016
Threads
13
Messages
1,312
Location
Southport NC
Good morning mudh8'ers! In the past I've had lunch box lockers, as well as welded up "spools" on my asst. Heeps, and trucks. I've always preferred the on-road manners of the spool type rearends...... no dis-engaging at speed being the biggest. My question is, on a bone stock 1991 would the rear hold up to being welded? My cruiser is used 50/50 on-road/off-road. Tire chirping and tight parking are not a major concern neither. Everything is stock at the moment, but I will be going up to probably a 35" tire.... max. (I've played the lift it game.... 2".....no 4".....no, need soa... and this time it will be OME 2.5" heavy......period!!
Majority of my wheeling is moderate Sand and mud.... I stay out of the rocks if I can. I would really appreciate, and value any or all your thoughts on this!...... thank you! Gunny
 
Good morning mudh8'ers! In the past I've had lunch box lockers, as well as welded up "spools" on my asst. Heeps, and trucks. I've always preferred the on-road manners of the spool type rearends...... no dis-engaging at speed being the biggest. My question is, on a bone stock 1991 would the rear hold up to being welded? My cruiser is used 50/50 on-road/off-road. Tire chirping and tight parking are not a major concern neither. Everything is stock at the moment, but I will be going up to probably a 35" tire.... max. (I've played the lift it game.... 2".....no 4".....no, need soa... and this time it will be OME 2.5" heavy......period!!
Majority of my wheeling is moderate Sand and mud.... I stay out of the rocks if I can. I would really appreciate, and value any or all your thoughts on this!...... thank you! Gunny


Full-float or semi-float?
Should be fine if you can account for C-clip removal on the semi-float axles.
 
Full-float or semi-float?
Should be fine if you can account for C-clip removal on the semi-float axles.

Does the c-clip on the 80 seem to fail at the worst time or for no reason at all? Like the Heeps are notorious for? I haven't heard much about them since coming over into the 80!
 
Just re-read and saw you have a 91, so semi-float.
The c-clip itself or the actual shaft?

With 35" tire and stock power you should be fine. The rear semi-float shifts are pretty big diameter actually.
 
Just re-read and saw you have a 91, so semi-float.
The c-clip itself or the actual shaft?

With 35" tire and stock power you should be fine. The rear semi-float shifts are pretty big diameter actually.

The clips themselves seem to come out quiet often on the Heeps if my memory serves me correct.
 
There has to be more opinions or experience on this....... the holy grail..... of Land Cruisers! Bring it....
 
If that is your preference, weld it.:meh: Be aware that an auto locker reacts differently in a full time rig, along with the CDL it almost acts like a select-able. So, your previous experience likely differs from the reality in this case?
 
Good morning mudh8'ers! In the past I've had lunch box lockers, as well as welded up "spools" on my asst. Heeps, and trucks. I've always preferred the on-road manners of the spool type rearends...... no dis-engaging at speed being the biggest. My question is, on a bone stock 1991 would the rear hold up to being welded? My cruiser is used 50/50 on-road/off-road. Tire chirping and tight parking are not a major concern neither. Everything is stock at the moment, but I will be going up to probably a 35" tire.... max. (I've played the lift it game.... 2".....no 4".....no, need soa... and this time it will be OME 2.5" heavy......period!!
Majority of my wheeling is moderate Sand and mud.... I stay out of the rocks if I can. I would really appreciate, and value any or all your thoughts on this!...... thank you! Gunny

Would it hold up? Depends on how good your welds are and how evenly balanced they are. It is a rotating assembly and does need balance to be on the road.

Just put in a lunchbox and be done. Easy and less hassle.

I would never drive a welded differential on a highway truck. Only for crawling or mudding.

Do what you want, but once you weld it, you have to torch it to get it apart.......
 
Would it hold up? Depends on how good your welds are and how evenly balanced they are. It is a rotating assembly and does need balance to be on the road.

Just put in a lunchbox and be done. Easy and less hassle.

I would never drive a welded differential on a highway truck. Only for crawling or mudding.

Do what you want, but once you weld it, you have to torch it to get it apart.......

That what scares me. Like tools r us pointed out, the previous vehicles I've welded did not have a cdl, so how this reacts is foreign to me. That's why I was hoping to hear from anyone that has done it already. And yes, to "undo" it is damn near impossible and I don't believe these thirds are just laying around! I believe I have a line on a mini spool.... that would be "the cats ass"!
 
If that is your preference, weld it.:meh: Be aware that an auto locker reacts differently in a full time rig, along with the CDL it almost acts like a select-able. So, your previous experience likely differs from the reality in this case?

I agree, that's what's holding me back!
 
your title claims it's an 81. if that's the case you should have a full-floater.

Sorry, I'm a Marine Grunt, not an admin poque! My 2 finger typing f'd up.... it's an 80!
 
I have an opinion but don't think you'd like it, so I haven't said it.. :flamingo:

Bring it.... just stand by when I commence to tearing you down.......♠
 
auto-locker + cdl is a magic combo. On my last rig I installed an aussie locker while it was full time and later converted to part time and the difference was night and day. I never noticed the locker while it was full time, if anything the steering seems to tighten up a bit and the truck drove a little better overall. Once it was part time I noticed all of the little quirks that everyone complains about(popping, clicking, etc)
 
auto-locker + cdl is a magic combo. On my last rig I installed an aussie locker while it was full time and later converted to part time and the difference was night and day. I never noticed the locker while it was full time, if anything the steering seems to tighten up a bit and the truck drove a little better overall. Once it was part time I noticed all of the little quirks that everyone complains about(popping, clicking, etc)

The thing I worry about though, and I have ZERO expirrience with an Aussie or any lunchbox locker, is the "un-loading" I hear guys complain about. Where they are tooling down the highway, let off the gas a bit, and the locker "unlocks" basically throwing them in the next lane! My kids are grown, I usually bring the 80 up by myself (following buddies), so I'm the only one to worry about, but I know I used up at least 9 lives between iraqx3 and the 'stanx2! Not wanting to flip the bird to the reaper yet!
 
I never had anything like that happen. The worst thing mine ever did was make a loud bang in slow turns, but only after the 2wd conversion.

I would go with the Aussie. It is cheap and easy to install.

The more I hear from people that have actually used them, the more I'm leaning towards an Aussie! How bad would it be to put one front and rear? With cdl the front should act "open" wouldn't it? Until cdl was engaged.
 
I think most of the unloading and popping comes from having a manual transmission and a shorter wheel base.
 
My aussie has never popped or unloaded like described. In fact I never hear it ratchet unless both front windows are down and making that tight mall parking space. It virtually is invisible 90% of the time. And like mentioned again that in combo with CDL+7pin mod almost makes it selectable. Zero regrets here with my setup. (not part time here BTW)
 
Back
Top Bottom