Water causing rough running

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 5, 2012
Threads
4
Messages
35
Well, now I've gone and done it. In preparation for some mechanical work under the front half of my 1991 LC I took my power washer to it to get the majority of road dirt and splattered oil/grease off everything. I would never do this to a standard car but the LC fords rivers, right? I knew the risks and thought it would be worth it. Now, 3 days later the truck is still running rough, mainly on acceleration. It acts as if running on 5 cylinders. I've put a timing light near each plug to see if the distributer is sending out and it seems like each plug is getting a poke. Squirted electronic cleaner in the plug caps to make sure of good contact. Checked all the vacuum tubes, all attached. There's no back or front firing so I doubt I've upset the timing. What should I be trying next? Or what can I do for a diagnosis? Could water have gotten into fuel delivery system? I would think it would be out by now after about 50 miles driving. Any ideas? Thanks in advance, Bob in Michigan.
 
This is why I don't bother pressure washing engines. I just saw a different thread on this.
Water gets into the plastic clips where harnesses connect on every sensor distributor etc and starts to cause corrosion.

In your case Bob start with the ignition components. Usually when you have an engine that stumbles on acceleration it's ignition related.

I would unplug the connectors at the distributor, coil pack, each spark plug wire on both side. Blow each connection out with compressed air and then after dry apply dielectric grease.

You most likely have water down in the spark plug tubes, compressed air nozzel while holding a rag over the hole will do the trick. Again dielectric grease will be your friend.

If you do all that and still an issue check the tps plug and finally the famous wiring harness by the egr.

It's also possible but unlikely that you knocked off a vacuum line, although I would expect a poor / racing idle.
 
Most often a miss, after being wet, is moisture in the distributor cap. Other than the TPS, the connectors are weather sealed. Aging can affect the sealing, both distributor and connectors, but I would rather find, repair that, before it's in the middle of a ford?
 
Forgot pull the distributor cap and make sure dry inside too
 
Had a similar issue after powerwashing before doing a bunch of seals. Compressed air down the plug holes cured it. I found one that was wet and didn't want to evap it off fast enough.
 
I know 3F is different, but I don't know how much. I've had moisture issues in my O2 connectors that sounds similar.
 
I know 3F is different, but I don't know how much. I've had moisture issues in my O2 connectors that sounds similar.

No. Moisture in O2 sensors don't cause an engine miss.
 
No. Moisture in O2 sensors don't cause an engine miss.

Okay... Mine was throwing code 26, idling really rough, running poorly. I unplugged O2 sensor connector, blew substantial water out of it, dried it out, plugged it back in. Problem solved. No other corrections made. So, Id say your matter of fact statement is not accurate. Then again, you said sensor not connector, like maybe you didn't actually read what I posted.
 
Thanks for all the ideas, sometimes it helps to have a set plan to follow instead of just stumbling through my own ideas. I'll let you all know how it turns out. Bob.
 
Gotcha. I thought you were saying the sensor. I Just got off a 12 hour flight
 
I think what the OP describes as a "miss" is really just rough idle.
If you start with a cold engine and she runs smooth and gets progressively worse as it comes up to temperature, then your O2 sensor wiring is suspect.
If it runs rough regardless of coolant temp, then look at your air intake tube, AFM connector, and as someone already mentioned, the soft vac lines on the throttle body. You might have blasted one off which could cause rough idle, depending on which one you popped off.

Remember, it's a 3FE. Not a lot of brains in the system. Always look for the simple stuff first.

Certainly take the time to unplug, blow out, and grease all under hood connectors. That's always a good thing to do.
 
Hi, Did you knock off one of the countless vacuum hoses? I water blast all our cruisers twice a year...no problems plus I hate working on greasy cars. Mike
 
OK, an update and some more info that I did not include originally. The battery is now dead, and it is not charging and I doubt related to a bad alternator, just put a new one in last year. When I first drove this after the water blasting, the red light above the voltage meter on dash was lit, so was the AT/oil lamp. Each time I drove it the lamps would come on less and less and finally not on at all, I assumed whatever was wet just dried out, but now with the battery not charging I suspect there is water in some connector associated with the charging system. I'll pull off the alternator connector and blow it out (I blew out most everything else I could find) and see if that makes a difference, in the meantime, any other ideas about water and battery not charging and rough idle and acceleration? Thanks, Bob.
 
The voltage, AT, and BRAKE lamps indicate the alternator is faulty. This would also explain the rough running.
Do not discount the alternator being faulty. Hang a voltmeter on the terminal on the rear of the alternator.
Was this an OEM rebuilt unit or an aftermarket one? Aftermarket alternators can have remarkably short lifespans.
 
Those were the lights that were on. I will check the voltage from the alternator tomorrow. Can getting water inside the alt ruin it? I just don't think it was a coincidence. It was just an aftermarket alternator. What does the forum suggest for an alternator? And where to source it? Thanks, Bob.
 
Back
Top Bottom