Vib and GRRR FIXED.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 6, 2007
Threads
29
Messages
211
Location
Ogden, Utah
To all that have Helped and gave input on my recent threads(another vib thread) I HAVE FIXED THE PROBLEM:bounce2::bounce::cheers::beer::beer::beer::beer::beer:. LANDTANK and FDZFILLMORE, I owe u guys a round. They helped me so much. I fixed the problem buy rotating my front DS and made "off phase" and it took about 90% of the vib away:). I can explain more if needed, but for know I just wanted to say "THIS SITE AND IT'S MEMBERS ARE FREAKIN AWSOME, AND I WILL BECOME A LIFER TO THIS SITE":cheers: to everone and keep it ROLLIN!!!!!!!!!!!!! Thanks John"WoodyFJ80"Wood
 
Sounds like his front shaft was in phase (u joint ears lined up) and he put it out of phase. (90 deg. perpendicular to each other) and it helped. Isn't the front shaft supposed to be out of phase from the factory? Mine was. It was suggested that I try to put it in phase to cure my vibes. Did not help. I ended up using a CV joint from a tacoma and that solved most of my vibes. I think what's left is the rear since I did the cheap ass "toss springs at it" lift. I guess they make lift "kits" for a reason. Whoda thought!:cool:
 
Correct, the front DS is out of phase, rear is in phase. No idea why. Apparently a lot of drive shaft shops will replace the front DS in phase since that's the way most are, something to note if you have a shop work on your truck.
 
I ask because I did the "throw the springs at it lift", then after a caster sweep added Slee's blue bushings. Now my front DS is vibing and Grrring. I would assume that I shouldnt have gotten a J lift w/out bumpers/extra weight, but I was planning for the future mods, so to speak! I could maybe check this possibility with the "phase". Is it in the FAQ? I dont remember seeing it.
 
I did install 850J's in the front and 863J's in the rear with 1" trim spacer in the front and had a vib and grrr after the install. Posted a few threads and got alot of feed back on what it could be and then narrow down things and trying things found the problem solver, put the DS out of phase (front DS), and kept the rear in phase and YEEE HAAAA problem FIXED!! Still planning on a ARB front and few other mods in the very near future. Any other questions please fell free to PM me. Thanks WoodyFJ80
 
When I bought my 80 I had a slight vibe at 45 to 50 MPH. When I switched the gears to 4:88's, that drive-shaft was doing some spinning. Vibes horrible right at 70 MPH... The damn speed limit.

Had the shaft rebuilt with new Yota joints. Still vibes. Had the D-shaft balanced, shop said horribly out of balance. Wanted to know how I bent it. Get it back, it's better, but still vibes. Told that it was my T-case or Tranny. I look on here for a while and find the phase threads in the FAQ. Look under there, in phase front d-shaft. I take it out of phase, 90% better. I'll be taking it back to balance. D-shaft shop said they'll do it for free. Couldn't believe it was supposed to be that far out of phase.
 
I did install 850J's in the front and 863J's in the rear with 1" trim spacer in the front and had a vib and grrr after the install. Posted a few threads and got alot of feed back on what it could be and then narrow down things and trying things found the problem solver, put the DS out of phase (front DS), and kept the rear in phase and YEEE HAAAA problem FIXED!! Still planning on a ARB front and few other mods in the very near future. Any other questions please fell free to PM me. Thanks WoodyFJ80

What caster correction did you use. Your signature indicates MAF brackets? Is that still current?
 
Yes, My MAF drop brackets are still in place with Org. bushings. Today driving to work, I did notice some vib is still present, but the vib is, I would say 80-90% gone. I am being very keen on every little noise now. Mr. Slee do you have any other ideas or poss. thoughts to help?
 
My setup is J's with 1.5" front spacer and custom arms, pinion pointing at the transfer flange. Did a bunch of messing with the shafts and mine runs the smoothest with both shafts in phase, but need to go to a CV in the front to make it right.
 
I notice alot of differance with the DS "out of phase". I am wondering why is it so differant for everyone, and with the same set-up??? I need to redo my knunckle bearings and seals, but I am confused with everyones thoughts and problems. You would think that we could solve this problem by now. But, Once again I DID notice a differance "out of Phase". It is so weird.
 
The problem is that all the trucks don't start with the exact same castor readings. This means that the solution for one may not work for another. I believe it is trial and error to find what will work.

Buck Buchanan
 
Its not all trial and error if you do your homework.
It comes down to castor readings and u-joint angles.
Putting the castor into spec can put the u-joint angle difference over the top if your lift is over 4". Then your into DC world
Unfortunately many fall into the no mans land between 3-4" where nothing really works well unless you have a lot of weight up front.
 
fzj80kidpen, I couldn't agree more, I do firmly beleive that I am in that no mans land, for I am running no extra weight up front, just stock set-up(bumber) . Hopefully to get an ARB in the very near future. This will help convince the wife. I think running J's with no weight makes a differance with this problem. Can't wait to add weight to the front end and see what or any differance it makes. Any thoughts to this?
 
Its not all trial and error if you do your homework.
It comes down to castor readings and u-joint angles.
Putting the castor into spec can put the u-joint angle difference over the top if your lift is over 4". Then your into DC world
Unfortunately many fall into the no mans land between 3-4" where nothing really works well unless you have a lot of weight up front.

I would agree that some homework is in order and yes it does come down to castor and u-joint angles.

I think your "no mans land" comment proves my opoint exactly. With the myriad of castor plates, castor bushings with different degree's of correction, control arms and drop brackets available, I feel it can become trial and error to find the perfect ride. No one should have to drive in a no mans land rig, the solution is there somewhere, even if that just means adding weight.

Buck Buchanan
 
I doubt that adding weight will hep the vib situation. While adding weight will improve the amount of caster you have it won't change the drive angles that much.

From our conversation I think you're light on caster and it's why I suggested reading the drive angle of that front joint. The idea is to get the front drive angle as close to 0* as possible AND have acceptable caster for a DC shaft.

With the lack of weight, the springs and shims installed I would bet you're in the negative caster region.
 
Landtank, I agree with you and everyone, and I am goin to redo my measurements tomorrow when I get home, and I wil post them on this thread. I am curious to see what the reading will be after putting the front DS "out of phase". And, hopefully alittle added weight in the front will get rid of the rest of the vib and grrr, seeing that 80-90% is gone.
 
You may find that the grrr comes from the rear shaft. I really think what's left of my grrr is rear shaft. I had it balanced and it helped a lot but not completely. I'm also using the MAF drop brackets for caster correction. I'm using the 4" ones. Which ones do you have? I did a lot of swapping of shafts and driving around with one or the other and thats why I think that most of my grrr is now rear shaft. Before the DC shaft I had nasty grrr. With front out I had mild grrr. With rear out I had louder but less frequent grrrr. I have not run with only front DC shaft yet, but my current grrr is about equal to after balance, rear shaft only grr. It's very mild and only under a very specific load. Maybe you try pulling shafts and locking the center diff to isolate your grr. That's what I did and I learned a lot. And got real good with a 14mm wrench! I'll be ordering Slee's rear control arm adjusters soon to hopefully get me out of no mans land since I cant go any higher or my 33" toyo open country tires would just look ghey! Who wants to buy my 33s so I can go 35!?
 
I am also running the 4 plus drop brackets. I was wondering about the rear as well. I am going to try your hints and remove them and see(hear) what it does. About your 33's, thats what I would like to run in mine. Where are you located and how much? Also, what rims are you running? And, whats the tread depth/miles on them? I am thinking about Slee's control arms as well. Did you get new panhards or are they stock? Well any way I just want to get away from "no mans land"

FYI: I measured my u-joint angle at the front DS and they are as follows:

5* then rotated 6/7* the dial is showing angle * to the
front of the LC.
Any input on the numbers? Does this mean I have 1/2* of caster?
Let me know Thanks John
 
Back
Top Bottom