stevebradford
In the shop
80 series parts. rear axle gone apparently I tried already.
$1 · Parting Out 80 Series Land Cruiser Complete
$1 · Parting Out 80 Series Land Cruiser Complete
VI: Buy/Sell/Trade, In Search Of (1 Viewer)
- Thread starter bikersmurf
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
- Thread starter
- #1,122
I'll pass... no interest in having someone handling my junk.
GTSSportCoupe
2LTE abuser
WTF? Haha! I hope they were thinking of something else when they wrote that.
Not sold on the paint job on that. Rare manual transmission model though.
Graham....300 us for rust free body Seattle
×
image 1 of 4
^^^needs bigger tires? Put a 3B with a turbo into that would be cool!
Yard Sale. PM me your offers.
- 60 series custom rear bench which raises and lowers and lays flat for a bed. Pretty cool actually.
- 2 x 60 Series center consoles. One has cup holders and the other doesn’t to allow for cable lockers.
- RHD 60 Series dash pad. Two very small cracks.
- RHD 60 Series cluster. Shows 281,000k
- Clutch Fan from something. Mounting holes are 1-3/4” beside each other and 2-1/2” across.
- 5 sets of driving lights. One set is PIA, one is fog. All are 7” except for fogs are 6”.
- 80 Series ‘90-01 grill.
- FJ80 ‘95-97 Toyota grill. BNIB.
PM me your offers. Need to make some space in the shop!
- 60 series custom rear bench which raises and lowers and lays flat for a bed. Pretty cool actually.
- 2 x 60 Series center consoles. One has cup holders and the other doesn’t to allow for cable lockers.
- RHD 60 Series dash pad. Two very small cracks.
- RHD 60 Series cluster. Shows 281,000k
- Clutch Fan from something. Mounting holes are 1-3/4” beside each other and 2-1/2” across.
- 5 sets of driving lights. One set is PIA, one is fog. All are 7” except for fogs are 6”.
- 80 Series ‘90-01 grill.
- FJ80 ‘95-97 Toyota grill. BNIB.
PM me your offers. Need to make some space in the shop!
Any of those lights CIBIE? The ones on the far left and the ones with the yellowish tinge?
Are they 12V or 24V?
How much for the rear seats?
Are they 12V or 24V?
How much for the rear seats?
Anyone have a shift ball bushing for a h42?
Tried toyota? I got one for an h55 a couple years ago, was pretty cheap.
For a cruiser part.
For a cruiser part.
Radiator for BJ60 I think 1983 to 1985, mine is not repairable..
- Thread starter
- #1,131
Heads up... SEARS has everything 50-70% off.
This includes garage door openers. Just bought a belt drive opener with remotes, a number pad, motion sensor, electronic eyes, etc... 149 vs 300.
I'll have a good chain drive opener for someone once it's installed. It has no safety eyes but works well. Free to anyone who helped... or dirt cheap otherwise
This includes garage door openers. Just bought a belt drive opener with remotes, a number pad, motion sensor, electronic eyes, etc... 149 vs 300.
I'll have a good chain drive opener for someone once it's installed. It has no safety eyes but works well. Free to anyone who helped... or dirt cheap otherwise
stevebradford
In the shop
- Thread starter
- #1,133
Is that what they're worth these days?
Not sure about their definition of restored... frayed seat belt, split seat covers, cracked dash, visible screws securing sheet metal over 1/4s, blue roof, dented bumper, red reflectors instead of vent covers... just to name a couple obvious things.
Anyone have a stock shift knob for a h42 and the t-case knob, also need 60 series tail light covers and 2 front seats
I might have a set of seats and rear lenses. I’ll check and get back to you.
Okay, thank you
I think I have a four speed shift nob new sitting on top of my tool box...its yours if you want to pick it up
Got the seats out of storage. PM’d you.
Ahh...shift knobs, I thought you meant the bushing on other end...so disregard my toyota suggestion above.
On another note, anyone have a tire groover ? Little front tires on my tractor are bald as hell. Should be enough meat there to carve out some treads so I can get another couple years out of them.
On another note, anyone have a tire groover ? Little front tires on my tractor are bald as hell. Should be enough meat there to carve out some treads so I can get another couple years out of them.
ISO: 2x 1.25" or 1.5" hubcentric wheel spacers and a dozen shank style lug nuts.
