Valve Guide Seals?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 23, 2006
Threads
4
Messages
34
I have been absent from this forum for a while, but have a question. Does anybody have any experience with an 80 using too much oil and replacing the valve guide seals? I've been through every option I can think of to take care of this oil consumption with an inexpensive solution. None of them have helped at all.

So, I've got the 80 (which I now consider a giant P.O.S. because it's cost me almost $5000 in about 18 months so far) at a shop in town which specializes in Toyota. The guy is conived that it must be the valve guide seals and recommends replacing them. I told him I'm going to think about it because I'm ready to cut my losses and sell the thing to somebody else who wants a 5000 lb paperweight in their garage. But, on the other hand, I've sunk so much money into this thing that I might consider having the valve guide seals done and then keep it for another 10 years.

Any input? Has it worked to stop oil consumption? If in fact it is the vavle guide seals and has been consuming oil for quite some time (at least the 15k miles I've owned it), have I done damange to the engine? Have I done damage to the point where putting the $$$ into the vavle guide seals is not a smart option?

Would love to hear any thoughts.

1997 80 Series
98k Miles
Phoenix, AZ
Using approx 1 quart every 1k miles

Thanks,

Brian
 
Personally I think the mechanic is a little out there.
My cruiser had 130k on it before I put on a supercharger and it used about 1 quart per 1,000miles so changing my own oil would add 2 quarts of Mobil 1 20 w 50 along with the balance mobil 1 10w 30. and it seemed to help some. Beleive it or not the sc basically stopped the oil useage. I now have 175k so I would give it some time and change the oil on time.
I am no expert but I have heard that some US car manufactures used to say 1 quart every 500 miles was ok.
 
I have been absent from this forum for a while, but have a question. Does anybody have any experience with an 80 using too much oil and replacing the valve guide seals? I've been through every option I can think of to take care of this oil consumption with an inexpensive solution. None of them have helped at all.

So, I've got the 80 (which I now consider a giant P.O.S. because it's cost me almost $5000 in about 18 months so far) at a shop in town which specializes in Toyota. The guy is conived that it must be the valve guide seals and recommends replacing them. I told him I'm going to think about it because I'm ready to cut my losses and sell the thing to somebody else who wants a 5000 lb paperweight in their garage. But, on the other hand, I've sunk so much money into this thing that I might consider having the valve guide seals done and then keep it for another 10 years.

Any input? Has it worked to stop oil consumption? If in fact it is the vavle guide seals and has been consuming oil for quite some time (at least the 15k miles I've owned it), have I done damange to the engine? Have I done damage to the point where putting the $$$ into the vavle guide seals is not a smart option?

Would love to hear any thoughts.

1997 80 Series
98k Miles
Phoenix, AZ
Using approx 1 quart every 1k miles

Thanks,

Brian

Brian,
There is no way a LC with 98K miles would have bad valve guide seals, just no way.

What are the symptoms? Smoke on start up? Smoke as you accelerate?
Do you have leaks? Is your engine clean enough on the outside to tell if you have new leaks?

I would suggest this, put something like RISLONE in your oil next time it is low. It is a light weight machine oil with extra additives
to clean up sludge; sometimes when an engine gets filled
with sludge and varnish, it will actually use more oil.

It will slowly dissolve any sludge. Then after a few hundred miles.
Change your oil, but before you do that, add an ENGINE Flush;
like a CRC brand(hard to find) or GUNK brand, doesn't really matter.

Let that circulate for 5-10 minutes before you change the oil; just
read the directions on the can. This will clean out any sludge, varnish, goop, whatever that sometimes can lead to increased
oil consumption.

Then change your oil and filter. If you prefer conventional oil
use Valvoline MaxLife 10W-40, if you prefer synthetic, then Mobil 1
"High Mileage" 10W-30 or 10W-40.

Your vehicle will take eight (8) quarts; be sure before you leave
the shop that changes your oil that it is at the full mark.
Then check it again the next morning after it has sat overnight
to be sure it is at the full make.

Then watch it carefully for leaks, smoking,etc. You should write down the exact mileage and date when it was full, then check your oil level at least once a week, and write that down.
You could reset your odometer also and not touch it until
the next oil change as a backup.

One quart per one thousand miles is too much for a Toyota with
only 98K miles; so I would doubt that it is real.

If it still is using that much oil, and not leaking it,
you could add something like BARS Main Seal leak stop (forget the exact name); it comes in a clear two component plastic bottle
and costs about $10 at Advance Auto.

IT WILL NOT HURT ANYTHING no matter what others may tell you.
All it does is swell up hardened seals; like valve seals, main seals,etc. It does not plug up your engine.

If you still have the problem after all that, then take it to a different
mechanic.

On the other hand, oil is cheap, and you could add a couple
of quarts between changes for many years and still come out
ahead compared to having the value seals replaced.

Good luck, and let us know how it turns out.

g
 
Brian,

Those are really, really low miles for valve guide issues but it's not my position to judge and the vehicle may have been mistreated or something. Who knows?

Valve guides are a place that oil consumption can come from but I'm not aware of anybody replacing their valve guides to reduce oil consumption on an 80. Plugged PCV valve ($20) is the #1 culprit, rings are also a possibility and so are oil that's too thin and an external oil leak. Finally, some oil usage is normal.

To me, the bottom line here is in the absence of some past abuse (flood car, prior engine work, very very poor maintainance) I would not rush out and replace the valve guides as the first culprit.

DougM
 
If your using 1 quart per 1000 miles I wouldn't change a thing. I think I've read here, 1 qt/1000 miles is the actual acceptable Toyota spec.

In addition to the valve guide seals, there are some wipers on the pistons. According to my local Toyota mechanic, his experience has been with respect to oil consumption this is a popular culprit. He said that he is able to change these without pulling the engine.

If your low oil light doesn't stay on your probably not hurting anything. I always top off before a trip, check it when I get there. I only notice oil loss if I stay in town doing short commutes for weeks on end.

It it come on then goes off after parking on an incline I check it.

What have you spent 5K on so far? PM? or something else.
 
If you haven't already, replace the PCV... $6.
As long as the motor's running fine (which it ought to be like new if you've dropped 5k on it... I have a bad feeling you've gotten hosed on some maintanance costs), I'd put a catch can on it (do a search, couple of home brew jobbers have be posted up).

That's it.
 
I JUST HAD MY SEALS REPLACED BUT I HAVE A CRAP LOAD OF MILES AND DONT KNOW IF THEY WERE REPLACED BEFORE OR NOT.
I WAS USING OIL LIKE CRAZY. ENOUGH THAT I DIDNT EVEN BOTHER CHANGING MY OIL. BECAUSE THERE WAS ALWAYS FRESH OIL BEING PUT IN. STILL RAN FINE AND DIDNT SMOKE AFTER IT WARMED UP BUT YOU COULD SEE THE VERY END OF THE EXHAUST WAS BLACK. MY CATS PROBABLY SOAKED UP MOST OF IT. AND WILL GO BAD SOON:whoops:
 
Thanks for the replies everybody. I'll try and tackle most of the things that were mentioned.

I agree that 98K is far too few miles to be dealing with this, but none the less, I am. So, I'm stuck with trying to resolve it.

I don't know if the car was abused prior to me. I don't think so, but one never knows for sure. I bought a one onwner which completely checked out at the dealership, including a wet/dry compression test which showed good compression and consistant accross all cylinders.

I've used oil additives and also replaced the pcv valve. Neither helped. The pcv valve was not clogged when I changed it, so I knew that was not it as soon as I pulled it out.

I've read every post in the world on oil and there are just way too many opinions to even know up from down on that one. But, I've used every major brand of oil in the past, including both conventional and synthetic, on other vehicles and never noticed one bit of difference in oil consumption. Currently running Delo 15-40 in it (that way I only need one type of oil in the garage).

I somewhat agree mechanic may not be 100% correct, but there are only so many places oil can go. It's not leaking a single drip. Smokes at startup every once in a while, but usually (95% of the time) it does not smoke. So, where would the oil be going then besides escaping the valve guide seals.

He did mention that he's seen the problem with valve guide seals more in Arizona than anywhere else in the country. He figures it's because of the heat and dry air. Sounds reasonable, but then again, once the engine is running, they are all running very hot, no matter where you live.

I understand it is technically within Toyota Spec to be using 1 quart / 1 K miles. I also know it's just plain wrong and the oil has to be disappearing somewhere (either leaking or burning). Makes me physically sick every time I have to add oil.

So, I'm at a crossroads. I think I only have three options:

1. Deal with it (and possibly kill somebody every time I have to add oil because it just makes me sick)
2. Do the valve guide seals
3. Rebuild the motor
4. Sell it and move on.

Anybody else have any thoughts?
 
Thanks for the replies everybody. I'll try and tackle most of the things that were mentioned.

I agree that 98K is far too few miles to be dealing with this, but none the less, I am. So, I'm stuck with trying to resolve it.

I don't know if the car was abused prior to me. I don't think so, but one never knows for sure. I bought a one onwner which completely checked out at the dealership, including a wet/dry compression test which showed good compression and consistant accross all cylinders.

I've used oil additives and also replaced the pcv valve. Neither helped. The pcv valve was not clogged when I changed it, so I knew that was not it as soon as I pulled it out.

I've read every post in the world on oil and there are just way too many opinions to even know up from down on that one. But, I've used every major brand of oil in the past, including both conventional and synthetic, on other vehicles and never noticed one bit of difference in oil consumption. Currently running Delo 15-40 in it (that way I only need one type of oil in the garage).

I somewhat agree mechanic may not be 100% correct, but there are only so many places oil can go. It's not leaking a single drip. Smokes at startup every once in a while, but usually (95% of the time) it does not smoke. So, where would the oil be going then besides escaping the valve guide seals.

He did mention that he's seen the problem with valve guide seals more in Arizona than anywhere else in the country. He figures it's because of the heat and dry air. Sounds reasonable, but then again, once the engine is running, they are all running very hot, no matter where you live.

I understand it is technically within Toyota Spec to be using 1 quart / 1 K miles. I also know it's just plain wrong and the oil has to be disappearing somewhere (either leaking or burning). Makes me physically sick every time I have to add oil.

So, I'm at a crossroads. I think I only have three options:

1. Deal with it (and possibly kill somebody every time I have to add oil because it just makes me sick)
2. Do the valve guide seals
3. Rebuild the motor
4. Sell it and move on.

Anybody else have any thoughts?

Brian,
For your piece of mind I repeat my suggestion that you flush the heck out of the engine;
many people do not agree with this tactic, just that I have done
it many many times and it helped with oil related problems
and never caused any problems.

After you flush it superwell, try Valvolines MaxLife 10W-40,
it really does help lower oil consumption and helps swell seals
including valve guide seals.

You could also make sure your intake is clean, not just
the PCV valve; ie: get a few cans of Valvolines Intake/Throttle body cleaner and spray it into the PCV Port that goes into the intake while someone keeps the engine running. Spray more into the other vacuum ports that go into the intake.

I would also use the BARs product at Advance Auto;
it will not hurt your engine, and most likely will help the oil usage,
really. I have used it and it worked.

There is a school of thought that oils meant for diesels should not
be used in gas engines; I do not have any experience with that,
just talked to a Mobil oil engineer (not the guy who answers the phone) but a real chemist engineer type, and he recommended
to not use oil meant for diesels in gasoline engines. FWIW.

RISLONE, ENGINE FLUSH, CHANGE OIL TYPE, BARS PRODUCT,
and be happy.
DO IT TODAY!!

G
 
Replacing more valve seals because of the heat in AZ sounds like horse s*** to me. It's hot in lots of places. Cruiser's are built to be used in every climate on the planet.

X2;
it is hotter in the engine that ouside in AZ; I have driven Landcruisers in the Middle East where it can get up to 130-140+
and that is the outside air temp!!

Sounds like a mechanic looking for work.

g
 
98k miles is not too few to have leaky valve stem seals. If you or the previous owner drive low miles on a not very regular basis, the stem seals take it hard as they dry out and then wear faster. My 94 has 135k and blows blue smoke for 5 minutes on start up, because I drive it maybe 3500 miles per year. When I went to look at the rig, it was idling in the driveway, never buy a rig that is idling in the driveway. That being said, I don't use a quart per thousand, so you need to go to a better or thicker oil or fix something else. I use the Mobil 1 High mileage in 10-30 and it keeps my consumption at a quart per 2000 miles. Another thing that can cause oil usage is a leaky injector. If you dribble gas into the oil, it changes the viscosity enough to allow it to burn off easier. The way to tell this is that you will not lose oil in town for short drives, but if you go on a long highway trip you burn like 2 quarts in the first 500 miles. A blackstone oil analysis will show fuel in the oil as well.
 
Relax. Don't let adding oil get you down - my brother once told me 'Oil is cheap' - and he's right. My '72 Chevy van that used a quart ever 60 miles of highway driving was a bit extreme, but 1000 miles/quart is hardly time to hit the panic button.

I wouldn't rule out valve stem seals, but they're enough work to change on this engine that I would baseline other things - compression, leakdown, general engine sludge (perhaps due to the POs neglect), etc. Change the oil a few times and run some miracle-fix-in-a-can if you like.

I would run 10w-30 (or anything slightly thicker than a 5W oil) - esp. in Arizona, and wait until you feel the urge for a head gasket job. I replaced the valve stem seals on a 2F 'cruiser engine 15 years ago, and they need it again, but I can live with a blue puff on the first 15 shifts on a cold day.

My '95 has burned about a quart every 1500 since around 100K miles, FWIW. When and if I do the head gasket, I will, of course, replace the valve stem seals.
 
Maybe I missed this....How much oil are you losing ? qts/mile(s) please ?
 
X2;
it is hotter in the engine that ouside in AZ; I have driven Landcruisers in the Middle East where it can get up to 130-140+
and that is the outside air temp!!

Sounds like a mechanic looking for work.

g

I totally understand the thought on this, but I think the guy's pretty honest. He's got a good reputation around Phoenix (was recommended from some on IH8MUD). He also ran a wet/dry compression test about 6 months ago and his thought then was that it's fine. He still thinks it's fine. I'm the one who goes nuts when I have an engine burning that much oil. He wasn't saying that the it is because of the heat necessarily, but just that it's something he's notice a little more often than where he previously lived (Texas, with much more humidity in the air).

He honestly thinks I can just keep driving it and adding oil and it will run another 100k. He's probaby right. But still, I HATE that.

I think his point may have been more about the lack of moisture in the air than the heat.
 
I'm still curious what you've spent $5k on in the last 18 months. Your rig should be like new.

I'll add up the receipts later tonight and post it here. I'm sure I'm exaggerating just a bit. And some of it was known when I purchased the rig, so I negotiated the price down accordingly. The expensive item was a front axle rebuild. Than ran about $1200. Then it had to be done twice. I had it done at the local dealer and they failed again 11 months later. Actually, I'm not sure if they failed, but the buildup on the axles was horrible. It could be that the first dealer never cleaned it up properly and the second dealer was trying to take advantage of it. Regardless, it was done free of charge the second time because it was under warranty. The second dealer was PISSED when I let him "talke me into it", then at the last second asked him to call the first dealer to have him fax over the paperwork because it would be under warranty. But he coudn't back down at that point so I had them do it again anyway.

Anyway, it just feels like the thing has nickel and dimed me like crazy. I recently read a post on costs of ownership where somebody basically split 80 owners into two categoris.

1. Those who are do it yourself folks that keep the costs down that way.
2. Those who are not, but have the money to pay somebody else to do it.

I'm neither. Single with a full house and a stay at home wife. I bought the Toyota because of the "Legendary Reliability" and the fact my wife could drive it for another 10-15 years. And it's blown up in my face.

As soon as I can, I'm putting her back in a Mercedes and forgetting about this Toyota stuff. MIght keep it as a third vehicle since I'm so far into it, but don't plan on having at a daily driver for much more than another year.
 
Back
Top Bottom