Valve Guide Seals?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I totally understand the thought on this, but I think the guy's pretty honest. He's got a good reputation around Phoenix (was recommended from some on IH8MUD). He also ran a wet/dry compression test about 6 months ago and his thought then was that it's fine. He still thinks it's fine. I'm the one who goes nuts when I have an engine burning that much oil. He wasn't saying that the it is because of the heat necessarily, but just that it's something he's notice a little more often than where he previously lived (Texas, with much more humidity in the air).

He honestly thinks I can just keep driving it and adding oil and it will run another 100k. He's probaby right. But still, I HATE that.

I think his point may have been more about the lack of moisture in the air than the heat.

Brian,

The lack of moisture in the air would not affect the level of moisture
inside the valve cover to any level that could measured or cause any difference. And either way, it would not affect the seals. Keep in mind, more Landcruisers are sold in the Middle East than any other region in the world; places like Saudi Arabia, Jordan, Turkey, Iran, Kuwait, UAE, Dubai, etc,etc. These places are hot and dry.

Flush your engine well and switch oils, like the Valvoline MaxLife; that is what it is made for; to swell seals to slow down leaks.

Let us know after you have done that, this weekend.

G
 
Brian,
Forgot to mention this about oils; I switched to Mobil 1 Extended performance synthetic a year and a half ago, and then noticed that my oil consumption went way up. I then switched to Valvoline MaxLife
10W-40 and it went back to what it had been; only about 1/2 quart or so every 3000 miles.

The point is; the type of oil you use can make a big difference in oil consumption;
don't throw in the towel quite yet.

g
 
Brian,
Forgot to mention this about oils; I switched to Mobil 1 Extended performance synthetic a year and a half ago, and then noticed that my oil consumption went way up. I then switched to Valvoline MaxLife
10W-40 and it went back to what it had been; only about 1/2 quart or so every 3000 miles.

The point is; the type of oil you use can make a big difference in oil consumption;
don't throw in the towel quite yet.

g

Gray,

Thanks for all your input on this (as well as everybody else). A couple of things. First, I noticed in one of your earlier posts that you're not sure the milage is accurate (because it's just too low of miles to be using this much oil), but I'm pretty confident it is. The PO had enough documentation for me to be comfortable with that. Plus, given the overall condition of the vehicle and compression tests, I don't think it has any more than that. So, I think we are dealing with actual milage.

Also, have you hear of MOA as an oil additive? I've had a copule of people recommend that (not from MUD). Would that be the same as RISLONE you recommend?

I'm going to give these things a shot. And most likely, I will keep this rig for a long time. Mostly because I'm too stubborn and pissed to get rid of it. I'll just keep it as a third vehicle. Can't do these things this weekend, but I'll get to it soon.

Thanks for the input. :-)
 
He honestly thinks I can just keep driving it and adding oil and it will run another 100k. He's probaby right. But still, I HATE that.

I think your Mechanic is wrong on this one.........



..........I say another 200k.
 
Gray,

Thanks for all your input on this (as well as everybody else). A couple of things. First, I noticed in one of your earlier posts that you're not sure the milage is accurate (because it's just too low of miles to be using this much oil), but I'm pretty confident it is. The PO had enough documentation for me to be comfortable with that. Plus, given the overall condition of the vehicle and compression tests, I don't think it has any more than that. So, I think we are dealing with actual milage.

Also, have you hear of MOA as an oil additive? I've had a copule of people recommend that (not from MUD). Would that be the same as RISLONE you recommend?

I'm going to give these things a shot. And most likely, I will keep this rig for a long time. Mostly because I'm too stubborn and pissed to get rid of it. I'll just keep it as a third vehicle. Can't do these things this weekend, but I'll get to it soon.

Thanks for the input. :-)

Brian,
Don't know about MOA; sounds like something with Molybdenum
in it; I wouldn't add that.

RISLONE has been around for something like 60 years, with improvements along the way; I have used it for about 40;
it "gently" dissolves any sludge, varnish, crud, etc.

In older cars, after you added RISLONE, the oil would turn
black, not brown, but black, from all the baked on varnish
and crud that it would dissolve off the internal engine parts,
valve covers,etc.

The idea is, add RISLONE (my magic milk), run it for a couple of hundred miles of so, then add the Engine Flush you can get at
any parts store right before you change the oil and put on a new filter. I don't leave the RISLONE in your engine; it won't hurt,
but that is not what you are aiming for now.

Sometimes in a real dirty engine, you need to repeat this flushing
in a few hundred miles.

Once your engine is clean, you can then add something like the Valvoline MaxLife (I'm probably starting to sound like a salesman for Valvoline); if that does not do it, then add BARs Main Seal stopleak.

Then keep track of the mileage and oil usage.

Good luck.
g
 
Gray,

Do you use the Rislone Oil Treatment or Rislone Engine Treatment for the first step you are talking about?
 
Gray,

Do you use the Rislone Oil Treatment or Rislone Engine Treatment for the first step you are talking about?

Here it is in outline format:

First; go to Advance Auto and buy RISLONE Engine treatment
and then Engine Flush, the one in the silver and red metal can.
(doesn't really matter, just get any 1qt Engine Flush)

Add RISLONE Engine treatment now; 1 quart; do not overfill

Run for 200-300 miles or at least one week.

Drive to your favorite oil change shop

Add 1 quart Engine Flush in the parking lot before you
pull up to the door for service. You will need a screw driver
to puncture the can and a funnel to add it through the oil fill cap.

Run engine for 5 minutes before having oil changed.

Ask the guys at the shop to please drain all the old oil out
very well as you have just added a flush. (this means,
they should have the drain plug out, the old filter out,
and the fill cap off while letting it sit for 5 minutes, at least)

Also, ask them to look very closely for any leaks BEFORE they
do the service because they will spill some oil on your engine
and front axle during the service. If they find any, ask them to point it out to you.

Have them fill it up with Valvoline MaxLife 10W-40 (8 qts) and new filter. Of course, ask first to be sure they have that in stock;
no matter what they tell you, use this exact type oil.

Check to make sure the oil is at the full mark before you leave the shop. Ask the guys to show you.

Reset your odometer after the oil change.

Take your car to a car wash directly after the oil change shop
and spray off the bottom of the engine and the front axle
where they spilled the old oil during the service.

Recheck oil level the next morning before you start the car.
Make sure the car is on level ground.

Recheck your oil level at least once a week, in the morning
before you start the car. Write down the findings and mileage.

When you start the car first thing in the morning,
look for any puffs of smoke, not water vapor,
but puffs of smoke as you first start and as you pull
away. You could ask your wife to watch for you.

If after 500-1000 miles it appears that you are still using oil
at a high rate, then add BARs Engine oil stopleak or their
Rear Main seal stopleak. 1 quart; do not overfill.

I can guarantee you, that if you do this as outlined above
your oil usage will go down.

Print this out and keep it in the car for reference.
Write down the mileage and oil added, if any
each week.

If you want to clean the fuel system, try to find
the BG 44K gas treatment; try NAPA, or get any
$5-10 fuel injection cleaner and add a double dose
and then fill up your tank.

Good luck.

Let us know how it turns out.
 
Back
Top Bottom