Two Keys to One?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 29, 2014
Threads
32
Messages
547
Location
Tacoma, WA
So the key I received from the PO only operates the ignition. I found this out the day I went to pick it up and locked the doors when we went into the bank. Came back out and couldn't unlock the door. Luckily one of the rear slider windows wasn't closed tight and we could reach the tailgate lock. Anyway, I pulled a door lock cylinder and got a key made at Mr.T for the doors. Now I have two keys.

I was told by some guy at a muffler shop (solid source, right?) that I can have a key cut with one side from the ignition key and the other side from the door key and it will work in both. Anyone heard of this or have experience?
 
Well, the key that I received from the PO is so worn, that it works in the ignition, but not the doors. I pulled the pass door, got the code from the door lock, and had a new key made from the code, and it will work in ignition and the doors.
 
What the muffler man said wouldn't work. The key is cut on both sides.

Unless the ignition switch was swapped I bet the key that starts the truck is just so worn that is doesn't open the door lock. Does the new key look similar to the old one?
 
Does you truck have a alarm "brain" under the drivers seat? If so, program a fob to it.

I bet it does and that is probably how this situation came about. PO never put a key in the door lock. Always used his fob to unlock.
 
You could also get a locksmith to replace the tumblers in either your door lock cylinders or your ignition switch to match each other. You might have to get the tumblers from Toyota.
 
My key only work in the drivers door and ignition, it won't work in the passenger door or hatch lock. So I'm going to do two things, one is order a new FOB since I'm tired of not having a remote to lock and unlock my truck, second I'm going to order a new key through Toyota and see if it will work in all the doors. My dealer told me a fresh precut key can be ordered off of the VIN so I won't have to take the door apart to get the code.
 
Thanks for the replies. This is not a case of a worn key. The keys are a different cut. I guess I'll just stick with using two keys until I'm ready to spend the money on having the ignition tumblers matched to the door key. I don't believe I have a alarm brain under my seat but I'll double check.
 
You could also get a locksmith to replace the tumblers in either your door lock cylinders or your ignition switch to match each other. You might have to get the tumblers from Toyota.

Toyota does not sell components, only complete key cylinders.
 
My key only work in the drivers door and ignition, it won't work in the passenger door or hatch lock.

You could have what I call "lazy locks". If the key cylinders are not regularly used (IE a passenger door or a tail gate because you always use a fob or the switch on the driver's door) they will fill up with debris and the lubricant dries up. To free them up spray the key with WD40 or similar and work it in and out of the cylinder several times. You will need to reapply the lube and also wipe the key down to clean off what it pulls out.
Eventually the tumblers will free up and start moving like they should.
 
I was told by some guy at a muffler shop (solid source, right?) that I can have a key cut with one side from the ignition key and the other side from the door key and it will work in both. Anyone heard of this or have experience?

Actually this is true for older Toyota vehicles prior to about 1990. The early two-sided keys only interacted with tumblers on one side. I had a 77 Celica and an 80 pickup. I cut the Celica code on one side and the truck code on the other side. That key worked in both vehicles. If you could not rotate the cylinder you pulled the key out and turned it over.
 
Depending on what side the wafers use I could custom cut a key but I would need all the information and it may not be feasible. Best answer is have the ign re keyed to the door lock. I can re key it for you for $40 plus shipping. I could also key a new cyl to your door key and ship it to you so you aren't out a lock cyl and starting it with a pair of pliers.

NEVER use WD40 in a lock unless you plan on thoroughly cleaning it. It gets dirty and gums up. I have made plenty of money cleaning locks after they gum up using WD40 or graphite. The best way is to start with some brakleen then use Super Lube dry flim.

https://www.amazon.com/Super-Lube-11016-Aerosols-Dri-Film/dp/B000RFRM4U?tag=ihco-20
 
Back
Top Bottom