Tuffy Security is Interested

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

We all have different items we want to secure against "smash and grab" thieves. I I looked at Tuffy, nice but expensive stuff. I would not buy anything that cost $300, nice as it may be. T

Here is how I addressed the situation:

I built a 1/2" square tube frame with legs that fit inside the lower armrest compartment on my 1993. For a top I cut a 10 ga top , with a piano hinge on the rear side, and a key lock in the front that engages the square tube frame. I left enough room at the top so the key can permanently stay in the lock when security is not needed. You could probably buy a little more height inside by bending the key over, but I did not think of that until later.

Granted the locked compartment is only as secure as the plastic console itself, but you will NOT open the top with a pry bar, without tearing the plastic off of it. Unbolting the whole thing is beyond the scope of the security i was shooting for.

Issues not well dealt with:
- some sort of spring to pop the top up so it is easy to get into. Right now, and for past five years, there is a piece of radiator hose jammed in there to lift it. Not pretty, but works. I need to fix that - i really do have higher standards than that would indicate. "Pretty is as pretty does" will carry you just so far.
- I planned to pin the frame work inside the armrest housing with screws so it would not pull out, but measured a little large, so just jammed it in there - it will take a jack to get it out, and there is no way to get a hold on it without opening the top. So, I guess the security of the thing, as far as it goes, works.

The work I have seen on this forum makes my poor effort look pretty lame, but it works, and I know some of the really accomplished folks here can make a better one. Heck, a simple lock on the lid would be at least some help, and I would have settled for that if I had been able to figure out how to do it.

Jack Nichols, 1993 LC
 
Count me in with a price tage of around $200. I am in design phase now for the LX guys. My "sub" enclosure and amp are bypassed as is the long since abandonded cd cassette thingie. I like the idea of a locking inner compartment. I wish I had the time to put into my idea, but if I can get a plug and play solution that's all the better.
 
Interested. Like everyone, it is dependent on the price. Also, a spoke for the Ham radio is a must.
 
Is this a dead idea? I haven't seen any updates since early in the year. I'd be interested as I found this thread looking to see about fitting a Tuffy in 80. But looking at how the standard 8" Tuffy fits, I'd be happy with that but would love to have one that fit properly and allowed for my rear leather seats to tumble.
 
Is this a dead idea? I haven't seen any updates since early in the year. I'd be interested as I found this thread looking to see about fitting a Tuffy in 80. But looking at how the standard 8" Tuffy fits, I'd be happy with that but would love to have one that fit properly and allowed for my rear leather seats to tumble.

Mine works and allows the second row seats to tumble? I also have my CB mounted and my ham radio installed out of sight, with all kinds of storage, with a very comfortable arm rest.....and the best part no waiting for the past 2 years :hhmm:.
 
I thought, I'd revisit this thread. Was hopeful, by now they'd be available for the 80 series. A proper made to fit Tuffy center console box. I was wrong.
 
Tuffy monitored this thread in the beginning. Once it became obvious that many people had completely unrealistic expectations of price verse features I'm assuming they passed on the idea. I know I would have.

Tuffy will build a custom model for anyone. The key is how many you'd have to buy/sell to offset the cost of design. I talked to them once about it but can't remember the numbers.

Typed poorly from my iPhone using IH8MUD
 
Have fun building your own.

Not too tough. You only need a few tools.
Build one that meets your needs: https://forum.ih8mud.com/80-series-tech/535396-new-dingo-project-ammo-can-console.html
DSCN0732.webp
DSCN0724.webp
DSCN0733.webp
 
Tuffy makes awesome products. As the old sayin goes, you get what you pay for. As with Tuffy, nothing but high quality. I just installed a complete Jeep JK full length console, fit and finish is top, no install issues. You are no way, no how, goning to get something for our Cruisers , for $300. The guy i installed the unit on his Jeep paid 650.00. And that was a deal. The 80's Cruisers are much bigger regarding the console, so i would not be surprised to see it go for around 700-800 for our rigs. Especially with seperate compartments, cup holders, power outlets, etc.

For those like myself who would really like Tuffy to pull through for our 80's and other Cruisers, looking for a quality , multi-purpose console, Tuffy would be my first choice.

I do not work for,,,,or represent TUFFY in any way, just been installing their products for a while, if you had one , you would understand the price tags that come with it.

Tuffy :, if you still are watching this thread, you got my vote..:bounce::bounce2::clap:

CRUISER TIME
 
I thought, I'd revisit this thread. Was hopeful, by now they'd be available for the 80 series. A proper made to fit Tuffy center console box. I was wrong.
Unfortunately, we were never planning to make this product as an off-the-shelf offering. It was originally requested that we make a custom production run, which would require someone to give us a definite list of the features they want. With what's been discussed here, $200 probably couldn't be met. :) We have to make (and sell) production runs of 100 to 500 units for many of the items we currently offer! As Downey said earlier, it quite often can't be worked out to provide a million features for a price people would want to buy it for and at a quantity we'd have to make. :frown:
 
http://concept.gamberjohnson.com/catalog/
Has anyone tried this companies products? I imagine you can piece together stuff and make something nice but it would be costly. I may try once I rip out the console when I put in the manual trans. I would rather have the "cop car" utilitarian look anyway.
 
I cut a 2" x 2-3/8" section out of the front of an 8" Tuffy, then re-welded and re-painted. The front sits flush with the shifter console. It looks stock with the 2" filler piece fabbed to cover the gap and house switches. If this is too complicated for a major manufacturer to offer, i.e. one additional bend to accomodate the floor hump and a bolt on filler piece, well......

Apparently Kevin at Wagongear is making a bolt in version. It would have saved me a couple of days messing around, and would not be surprised, if it's superior in every way.
 
Last edited:
This interior fabrication company in Australia makes consoles for the 80. Kinda pricey at about $500 plus $50 to $100 for shipping. Their design is modular and they can build it to order for that price.

80_Series_Floor_2.jpg


The E brake is on the wrong side, but this was their reply regarding that issue:

We would be happy to ship a console to the US and have done so in the past. Before manufacturing anything, we would prefer if you could send us some photos of your vehicle's interior so we can confirm our patterns match the shape of the floor, interior colour, dashboard layout, etc. If you have a camera phone, please email the photos to us at this address.

We have established a strong market presence here in Australia over our 35 years of trading and are currently looking into expanding internationally. There is also a strong demand for our products in South Africa, New Zealand and the UK. If you have any information or contacts in the US that would be interested in this opportunity we would love to hear from them. We have an extensive library of vehicle information that would literally take years to try and duplicate. Our heavy duty cargo storage drawer systems that are designed to be vehicle specific are also a lucrative opportunity for franchising internationally.
 
Last edited:
The Tuffy full center console for Jeep JK is $467. https://www.tuffyproducts.com/p-213-jk-security-full-console.aspx I would assume something similar in features would run the same for an 80 series. (replacing everything including the shifter surround)

If a good number of folks are willing to spend that kind of money ($500+/-) I may be convinced to work with Tuffy to have something made. Tuffy is within an hour from Durango, so somewhat local to me.

Personally I feel the area around the shifters offer a lot of mounting possibilities and I wouldn't want to bother simply replacing the bucket under the armrest. I also would want a clean and OEM look. (not cutting corners to save cost). Just my $.02

If that type of product/cost interests you post up.

Current interested parties:
Neal0124

Pic of JK unit for reference

213_4_.webp
 
Last edited:
Back
Top Bottom