Transfer Case lever- which one?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 24, 2006
Threads
279
Messages
5,216
Location
97707
I have several levers that I had powder coated. There is two differant angle to them. I personaly like the greater angle to the one.

Opinions and reasons why they are not the same??
P1010192.webp
 
IMHO, the greater angle version would put it closer to you and easier to grab, no? I find that I wish the angle was a little greater on mine becuase with my 4 point harness seat-belts, mobility is tough and in general, it is just a tad bit much of a reach for me to the t-case shifter.
 
I was thinking of making mine shorter because when in 4 low I have had passengers accidentally knock it in to neutral. One time was when I was climbing a pretty damned steep hill....Exciting for sure
 
yep, my brother is 6'4" and he did the same thing to me once while wheelin a section. would this not be all the more reason to use the more angeled version to get it out of the way of passenger knees/legs?
 
AATLAS1X said:
Opinions and reasons why they are not the same??


attachment.php




The one on the left appears to be a stock piece.

The one on the right appears to have been bent like that at some point, possibly to clear the heater from the driveline moving forward from a engine conversion.



The one on the right would put the shifter lever further from the operater/you Kevin, not closer. ;) (and be even more in the way/prone to being kicked by a passenger)


:beer:
 
oops.... I stand corrected. :o

I went to SOR to look at the offending piece before posting and thought I had the orientation correct (#2 on their 4/75-8/80 4 Speed) - but I guess it's orientation triped me up.

well hell - I change my mind then.... :)

( I guess Floyd Landis cracking in the Tour today still has me a bit shaken and not thining right)
 
Just install/fabricate a twin stick and end the side to side lever movement BS...


:beer:



BTW-


wantatlc said:
(I guess Floyd Landis cracking in the Tour today still has me a bit shaken and not thining right)


Is this the American that has been leading off and on over the last couple days...
 
Poser said:
Is this the American that has been leading off and on over the last couple days...

/start hijack/

10-4... and he had the worst case scenario happen to him today and one of the final crucial stages..... BONK and had no teammates to come to his aid. major 10 minute disaster that put him from 1st in the GC to 11th... no chance of winning now... and he was our real true USA hope too bring it home.

7/20/06 UPDATE - I might have to eat my words - as many of us would - after today's events. Landis did the virtually unthinkable and pulled a major stage win out of his ass after a horrible bonk yesterday. Traditionally, a bonk like yesterday's size spells the end of a Tour, but he hammered the field today (nearly solo after his team pulled and cracked leaving him fresh) and an unprecidented effort to dig himself out of a virtually insurmountable hole and back up to 3rd from 11th and now only a mere 30 seconds back!! with the last defining stage argueably the final TT on Saturday - he is known to be the best TT guy in the field.

hell, he just may do it.....

/end hijack/
 
Last edited:
I was thinking one was bent, But I bought it complete and no marks in the metal from a vise or signs of a torch.................We sure its bent and not from a later model??
 
If this is going into the White truck you are building, I would install the piece on the left, as it is likely 'period accurate'... ;p
 
Poser said:
If this is going into the White truck you are building, I would install the piece on the left, as it is likely 'period accurate'... ;p

But if it was from a 60 it would be the larege thread, correct? Since the knob will not interchange.
 
Back
Top Bottom