Top Off & Seatbelts....

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 19, 2006
Threads
21
Messages
62
Location
Southern Ontario
My seatbelts are mounted to the hard top -- I assume that most 40's are similar. It appears that the upper shoulder strap could be easily moved to the roll bar.... what about the lower portion where the actual belt is fed out of ??

Where can this be moved to retain the seatbelt ? Pics or advice would be appreciated... THX

Mark
 
on my 77 I welded a piece of 4"x4" plate steel to the lower part of my cage. Drilled holes to stick the bold and nut to. The other hole is for the guide. My plate steel is 3/8" thick. ccot makes bracket to use for that, it goes onto the bolts of your cage on the wheel well. I bet sor.com has some also.

I leave the seat belts attached to the cage even with the hard top put back on.

DSC01477a.webp

DSC01479a.webp
DSC01477a.webp
DSC01479a.webp
 
Last edited:
Sorry, Bull -- good points...

Cruiser is a 1980. Both the upper shoulder (pivot/feed?) and the lower belt feed are bolted to the inside of the hard top. It does not look (to me anyway) that there are seatbelt ready holes. Now the PO had the roll bar out and powder coated silver, so those holes may have been there at one time.
 
Mark - CdnCruiser said:
Sorry, Bull -- good points...

Cruiser is a 1980. Both the upper shoulder (pivot/feed?) and the lower belt feed are bolted to the inside of the hard top. It does not look (to me anyway) that there are seatbelt ready holes. Now the PO had the roll bar out and powder coated silver, so those holes may have been there at one time.

Your seat belt attachment is problematic at best. The factory seat belts that I have seen are all mounted to the roll bar. I have not seen the setup you describe. I would be very concerned with the strength of the top mounting points in a crash. Those mounting points can not start to compare to the strength of the roll bar mounting points. I would correct the current layout. If you think about it, the top is meant to come off. With the top off the vehicle still needs to meet the DOT requiement for seat belts. That alone would lead me to believe that the PO changed it for some reason.
 
bsevans said:
Your seat belt attachment is problematic at best. The factory seat belts that I have seen are all mounted to the roll bar. I have not seen the setup you describe. I would be very concerned with the strength of the top mounting points in a crash. Those mounting points can not start to compare to the strength of the roll bar mounting points. I would correct the current layout. If you think about it, the top is meant to come off. With the top off the vehicle still needs to meet the DOT requiement for seat belts. That alone would lead me to believe that the PO changed it for some reason.

Mine(6/77) were bolted to the top just like he described.

You can see mine at the top.

DSC01432b.webp
DSC01432b.webp
 
Last edited:
In my 78, 77, and 73 FJ40s the seatbelt was always mounted to the tops when I got the trucks, then I moved them to the Rollbar where I usually had problems with the tensioners in the belts for some reason.
 
My 8/78 came from the factory with the seat belts attached to the roll bar. I understand that the attachment to the top is used, I just question if it was the approved placement in the US due to DOT requirements. I just do not understand how Toyota would expect the owner to move the seat belt attachment points every time the owner took the top off and then back on. Since the late 60s or early 70s seatbelts have been a federal requirement and not an option. This is something Toyota had to meet for every configuration of the 40 - hard top on or off, soft top. Think about the liability to Toyota when the owner took the hard top off and did not relocate the seatbelts to the roll bar and had an accident. Now it maybe that Toyota shipped all 40s with the attachment to the hard top and the US dealerships moved them to meet DOT requirements. It's interesting and if someone knows the history around this I would like to here it. The next time I'm at the dealership, I'm going to ask.
 
Last edited:
My 74 did not have a hard top when I bought it, the top of the harness that you have bolted to the hard top was mounted to the bottom of the 2 bolts that hold your rear bar to the center bar. (basically the bottom bolt of the 2 on your rollbar in the picture).
 
I have a similar issue albeit slightly different on my '74 FJ40. One of the previous owners removed the stock roll bar and put in a custom cage. The owner didn't allocate anywhere for 3 pt belts to attach so the Cruiser only has lap belts. So...I've been searching for ways to retrofit the cage to attach 3 pt belts to it.

I don't have a welder or ability to welds tabs so that is out unless I want to pay someone to do it for me including having to respray or powder coat the cage. Someone suggested just drilling a hole through the cage to attach the belts which I really don't want to do either if I can avoid it.

So, has anyone ever thought of or used "roll bar" or shaft collars such as those found here?

http://www.climaxmetal.com/

I would like to use something like these in the rear as well to retrofit in 3-pt belts in the back for the kids (unless I end up using seats with integrated 3-pt belts).


Here are some links to other ideas I have come across that some may find useful:

http://home.off-road.com/~leve216237/Seat%20Belt%20Attachment.htm

http://fourtreks.com/roll_bar.html
 
My 74 never had a shoulder belt. It was a factory soft top ( Now has hard top) It has only had the lap belts from day 1. My Dad was the PO so I know this to be true.
 
As old as mine is, it did not have anything but lap belts. I drilled a hole in the roll bar and welded a nut to the bar, seems to work OK. I also made a simple "L" bracket for the tensioner and use the same bolts that fasten the rollbar. Dunno if it is DOT or not, but it is better than it was....;)
seatbelts 003.webp
 
Thanks.......

....for all the discussion and pics ! Its been a big help for deciding what to do next. The attachement to the hardtop I have looks completely normal/factory like some of the others.

That being said, I agree completely -- why would they not account for the idea that the top comes off when it came to seatbelts ? :confused:

Thanks again everyone -- as always, my question is answered thoroughly !

Mark
 
So Mark...

What are you going to do? I would be interested in knowing which path you have chosen as I am in somewhat the same boat...:rolleyes:
 
Mark, I've been removing the top every year for 25 years off my 5/81 cruiser. My belts have always been mounted to the roll bar and I have these funny little rubber plugs in that spot on my hard top. Always wondered what they might be for. After reading this post I had to go out and check that little plug...damned if it isn't threaded for a shoulder harness belt underneath the plug. Another odd thing was the fact that the later years didn't have any windshield knobs to hold the w/s to the dash. Instead it was a long bolt covered by a plastic side window vent. Makes me wonder if Toyota was already thinking of discontinuing the removable top as they did with the 70 series in 84 I believe.

Don
 
Well..........

Since I am far from a 'fab' guy it seems to me my best option could be this:

Moving the upper shoulder pivot to the roll bar - that seems to be an easy item... as a few have mentioned, it looks like it should fit without any mods - just loosen a nut !

For the tensioner, what I was thinking was some heavy gauge steel in an 'L' shape braket -- one part bolted (or welded for strength) to the floor and the other available to bolt the tensioner to..somewhere close to its current location but off the hard top.

Will keep you updated - but be forewarned, I am a slow mover !

Mark


corsair23 said:
So Mark...

What are you going to do? I would be interested in knowing which path you have chosen as I am in somewhat the same boat...:rolleyes:
 
I would make sure the tensioner is in the same direction as in stock form. Isn't there weights in there to lock them up during braking or collision? Just my guess. Or does it just work on speed of pull?
 
Interesting....

I hear you on the windshield thing. What I assumed were the long bolts I EXPECTED to be holding the windshield, was nothing more than holding the PO's aftermarket 'dash' cover. These bolts had the little platic handle type set-up and looked as if they threaded thru the dash on an upward angle into the windshield.

I know exactly the bolt you're referring to as I have the same side window vents -- one just removed because the plastic had cracked and busted anyway.

Anyway -- the longaround point to my response was...

...perhaps you are right :grinpimp:



wapitidon said:
Mark, I've been removing the top every year for 25 years off my 5/81 cruiser. My belts have always been mounted to the roll bar and I have these funny little rubber plugs in that spot on my hard top. Always wondered what they might be for. After reading this post I had to go out and check that little plug...damned if it isn't threaded for a shoulder harness belt underneath the plug. Another odd thing was the fact that the later years didn't have any windshield knobs to hold the w/s to the dash. Instead it was a long bolt covered by a plastic side window vent. Makes me wonder if Toyota was already thinking of discontinuing the removable top as they did with the 70 series in 84 I believe.

Don
 
Back
Top Bottom