The Daily Chat Thread

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Kinda cool

Ian just sent me a note, he and his band are going to be in the studio monday doing some recording.
They will be using RCA Studio B down on Music Row in Nashville.
Elvis used this studio to record 150 of his songs, Dolly Parton, Chet Atkins, Willie Nelson, Waylon Jennings are some of the other artists who have recorded there!

The Past » Country Music Hall of Fame
 
green40 said:
Ian just sent me a note, he and his band are going to be in the studio monday doing some recording.
They will be using RCA Studio B down on Music Row in Nashville.
Elvis used this studio to record 150 of his songs, Dolly Parton, Chet Atkins, Willie Nelson, Waylon Jennings are some of the other artists who have recorded there!

The Past » Country Music Hall of Fame

That's awesome! :)
 
Just checked out gotpropane.com, looks like $850 to get set up, not sure where to mount the tank?

If it was me I'd go with a 3FE. From what I've read all you need is to drill out the bell housing for the larger bolts. The engine mounts are identical to the 2F so it should drop right in.
 
If it was me I'd go with a 3FE. From what I've read all you need is to drill out the bell housing for the larger bolts. The engine mounts are identical to the 2F so it should drop right in.

What is it out of? fuel injected? horsepower?
 
what I read was that the bellhousings changed for the 3F in that the bolts used to mount the bell housing to the block were bigger and you just needed to open them up on a 2F housing for it to work. But most actually source a 3F housing for some reason and those did come on the later FJ60s. Those hjave a casting mark "3F" on them.

Both HP and torque are up from the 2F but I'm not sure what the numbers are.

The only stickler might be the need to add the speed sensor circuit. The sensor itself is located on the end of the speedo cable at the t-case. It's a simple 3 wire sensor from what I remember and shouldn't pose any big issues.

I'd be happy to help out with the wiring if it gets that far.
 
Tom, Is your engine an F or 2F?

Here's a thread. https://forum.ih8mud.com/hardcore-corner/286094-fj40-build-advice-opinions.html

I had an FJ62 that I sold to Higgo. My plan was to put the engine in an FJ40 along with a 5 speed and split case with the Advance Adapters 4:1 crawler gears and do a springover with the FJ62 axles. I think that would be good for the road and the trails since you lose 1000 pounds over the weight of the FJ62. Then I realized the T/C gears and tranny were going to run $4K and decided it wasn't worth it.

Mark Whatley always felt the 2F with the stock Aisin carb set up properly was capable of extreme angles.

Here's some comparisons of a 3FE and 2F. https://forum.ih8mud.com/40-55-series-tech/200762-f-2f-vs-3f-torque-differences.html#post2965015

I guess my main question is why do you want to swap the motor or inject it? A 2F makes just about 200 foot pounds from about 1000 RPM into the 2000's. Heavy crank and flywheel makes it a great trail motor. You don't drive your rig on the road, so what is the problem?
 
Last edited:
Swedish Mile - RIP

Those of you who have enjoyed the Swedish Mile in the past will be saddened to learn that it is now only a hard pack road with a couple 25 foot long puddles. According to a local landowner that we spoke with on Sunday, the beavers are a pain and the Fish & Game gave him permission to remove the dam and shoot the beavers. I'm not sure if any beavers have been killed at this point, however, the landowner removed the dam last week and the water level in the wetlands dropped about 2 feet in 2 days. If this was the middle of summer, the stench of rotting vegetation and exposed swamp bottom would probably be overwhelming. The deep drop that is west of the camp site located along that trail is now only a couple feet deep.
 
Back
Top Bottom