Stiff suspansion

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 22, 2002
Threads
62
Messages
1,704
Location
Brownsville,Tx.
I have an 79 fj40 with a 350v8. I insatalled a 4" suspension from a Skyjacker along w/shocks, also a shackle reversal from man a fre in the front. The rear was the same 4" leaves but with shackles from cool cruisers stout something. the cruiser is level. it's not with the front end higher then the rear.

when I go over a speed bump the front end jumps and it feels like I don't have any shocks in the front.

what do I need to make it a little more enjoyable?

the used of the cruiser it's mostly a trail rig and a daily driver.
 
Unless you plan on putting on a winch or significant bump, you could try removing a leaf or two from the front end. You can do this because you took out the heavy 2F and put in a 200lb lighter engine.

I would also take each spring pack apart and slip plate the hell out of them.
 
I have had that same lift on mine for 3+ years now and it's just now starting to loosen up, a little.

In hind sight I should have done an SOA convert w/ a removable trac bar for road drivin'. Hind sight being 20/20.

Oh, and ditto on the shackle suggestion.
 
How about adding a hoop for double shock? would that help? I like the one that Sams offroad sells. the Question is does it work?
 
Put a heavy ass winch bumper and winch and high lift up front. Are you using heavy shocks? Rancho 9000 are adjustable; I run mine on the all the way soft setting. Rides better that way.
 
double shocking is a bad idea...makes a stiff ride worse, and costs you money....

if the springs are new, you do need to break them in ....repeated flexing of the packs in a ditch-ravine will suffice....

Skyjackers come stock with opened wraps and with nylon tip inserts.

Shackle angle may be a concern,......something to check on the front reversal setup (haven't seen a set of directions that were correct yet.....)
 
Well the shcakles used in the front end are stock I bought them from Daniel/Whimberly 4x4 up in San Marco,Tx. The rear shackles are as I mentioned from cool cruisers 2" or 2 1/2".

Woody what do you mean by angle to check?
 
does the front shackle angle over the springs, is it verticle, or does it lay back away from the spring packs?

http://www.ih8mud.com/tech/woody/shackle.html

that's what I did to my rear mount to add flex and help the ride a bit....

also, did you get hydro or nitro shocks with the kit? nitros will control better, but be stiffer.

I'll wager your shackles bolts are too tight, and that that springs need to be broken in tho....
 
At this time I don't remeber what type of shocks I have, but I will loosen up the bolts in the front shackles. the angle in the back it's a 90degree. it's pretty much straight, but the back it's not the problem. it 's the front end that bounces bad. I will losen up the bolts too, but the front has little anglel
 
I'd pull a leaf out of the front end, and see where that puts ya, that SBC weighs less than a F series motor...

I have been running the lift for 2 years, after I flexed it hard a few times it softened up. It was never bouncy.

You may have the hydro skyjacker shocks that came with my kit.

Now the truck rides great. It may be a little stiff for some but it is a very controlled ride.
 
I just went through the same problem, Bob at TPI had the solution. Try puting the cruiser on stands so that the springs hang free then spray motor oil betwene the leafs. This improved the ride on my fj-40 by 50% instantly.

Also check for binding bushings.

Matt
 
Back
Top Bottom