Steering Stabilizer

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 29, 2014
Threads
12
Messages
51
Installing OME steering damper on my 1970 FJ40 (maybe). Don't see any holes for the bracket on the frame. They don't come pre drilled I guess. So I go to mark my holes and there is a rivet right where I need to drill. Anyone else have the same problem? I am trying to restore to as close to original as possible. Does anyone know how these came from the factory? I really don't want to drill my frame if it's not necessary. What about driving it without the damper?
 
dsc01350-custom-jpg.302420
 
Got no holes in that location, but there is a rivet inside frame crossmember very close to where I need to drill one of the holes. Rivet does not shoe underneath, just inside.
 
If your alignment, shocks, and steering components are good, you may not need a damper at all.
Many people, including myself, run without one.
My theory is that it's there because many of these trucks ran in very severe environments around the world with sub optimal maintenance.
A damper may allow you to run smoothly with problems in the steering/front end. Another way to look at that is a damper may mask developing problems in the steering/front end so that you don't know they are there.
 
If your alignment, shocks, and steering components are good, you may not need a damper at all.
Many people, including myself, run without one.
My theory is that it's there because many of these trucks ran in very severe environments around the world with sub optimal maintenance.
A damper may allow you to run smoothly with problems in the steering/front end. Another way to look at that is a damper may mask developing problems in the steering/front end so that you don't know they are there.

Thanks for the reply. I think I'll run without it for now and see how the front end feels. All new joints etc. and not planning on any rough terrain. I can always sell it with the vehicle and new owner can install it.
 
I would hate to be in a position of suggesting something that might turn out to be unsafe on your vehicle.
I'm just saying that it works for me. Before I got my front end realigned, especially the caster, it would not have been safe to run without one.
Be careful and start out slowly.
 
it's not there to cover up for poor maintenance practices, it's there to help protect the steering gear, bell crank and ball joints and as an aside, your thumbs.
 
Since I took everything apart and re-assembled it, I am going to take it to my alignment guy to get the toe-in and alignment etc. done properly. Would it make more sense to install the stabiliser before that or after?
 
Chances are your "alignment guy" will tell you that he can measure but can't adjust the caster. Take a good look at that number.
If it's off, as it often is in lifted vehicles, it can be a problem and should be fixed. Search here and you will find sources for caster shims.
 
Chances are your "alignment guy" will tell you that he can measure but can't adjust the caster. Take a good look at that number.
If it's off, as it often is in lifted vehicles, it can be a problem and should be fixed. Search here and you will find sources for caster shims.
Camber either--toe is the only normally adj available
 
I realize this thread is old, but I have the same issue, did you find a place to mount it?
I also have the bracket on the crossmember but no hole in the center arm
 
since somebody replace your original components you can put one on the axle to rod

an aftermarket SS

Recommendations on aftermarket units? Or can I simply the bracket for the axle? I have the shock and bracket for rod.
 
The way I see it you are screwed with almost anything you do:
1. Get all the alignments perfectly corrected, then go into rough off road terrain and knock all the alignment back out of adjustment.
2. Add a steering stabilizer, then watch your big off road tires wipe the stabilizer out in about 6 months of highway driving alone.
 
Back
Top Bottom