small bolt pattern 4x4 Labs highsteer

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

nat

Joined
Sep 20, 2005
Threads
169
Messages
1,990
Location
Los Gatos, California
Has anyone done this? I need to measure my knuckle pattern, but I am sure it is the smaller pattern in my 1972 FJ55. I am SUA with FJ60 PS and want to improve my steering a little more. Has anyone had any problems with breaking the studs? I really want to get the 4x4 Labs Highsteer kit, it looks totally bullett proof. :cheers:
 
Your steering will not be bullet-proof on a small knuckle...



If you are going to drop the cash on this quality hy-steer, convert your knuckles to the later style, and be done with it....


Are you still using drum brakes up front?
 
I have 4 wheel disks, fj80 master, fj60 booster.

What has to be done to convert the knuckles? Do I just swap the housing?
 
I've had studs break on mine twice, once with the stock steering and once with the 4 x 4 hysteer. Both times it was because the studs came loose out of the knuckle. After a breakage at CM 2004 one of the guys from Rice on the Rocks reccommended welding the studs to the inside of the knuckle. Well I didn't take his advice and I used red loctite instead. His advice should have been taken, a year later I had to trailer my rig out cuz of broken studs again. Now they are welded.
 
Thats good info to know. Is there a difference in stud diameter with the two different patterns?

If you welded it and they broke, you could be S.O.L. Is it possible to have extra studs?
 
nat said:
Thats good info to know. Is there a difference in stud diameter with the two different patterns?



11mm for earlier....pre-1979 knuckles.


12mm for later.




You could carry extra studs....but you may need to carry a bridgeport to dig the broken stud out of the knuckle also...as it is not simply going to 'back out'.... ;)



:beer:
 
My pattern appears to be approximately 1 3/16" X 2 3/16" is this the small or large pattern??


Can't I just tow a bridgeport and get a 12volt to 240volt 3 phase converter :confused: ;)
 
AlaskanWheeler said:
Along with the larger knuckles; some ARP knuckle studs would also be a good idea.

Where and what are the ARP studs. I am building up my SOA axle with the small pattern knuckles and used new OEM studs - the change in fit was really noticable from the old ones.

I wish I had gone with the 12mm knuckle housings - but it is too late know. Going to carry 2 spare knuckles on the trailer - would like to use the ARP's? you are referring to.
 
marlin sells studs with torqs head s i have themon my 40
 
AlaskanWheeler said:
Along with the larger knuckles; some ARP knuckle studs would also be a good idea.


Click on the Yellow ARP link :grinpimp:
 
The larger pattern knuckles should be common as dirt. They came on all the 60s and the minis from 78-85. You can use everything but the steering arm and the lower trunion. You will also need the larger cone washers.

Dropping the cash on a high steer would be foolish without picking up some bigger knuckles, IMHO.

Luke at 4x4 Labs is likely to tell you the same thing.
 
Sputnik40 said:
Where and what are the ARP studs. I am building up my SOA axle with the small pattern knuckles and used new OEM studs - the change in fit was really noticable from the old ones.

I wish I had gone with the 12mm knuckle housings - but it is too late know. Going to carry 2 spare knuckles on the trailer - would like to use the ARP's? you are referring to.


Sputnik40 said:
Not working from on the oriface computer - will try from home :doh:

Link might work, but the studs won't...




These WILL NOT thread into your older, smaller pattern knuckles as your studs are 11mm diameter, and the newer knuckles use a 12mm diameter stud, which is what the ARP stud kit is for.




:beer:
 
Dennis@Moab said:
marlin sells studs with torqs head s i have themon my 40



Those are simply a new Toyota stud....they are not anything special...I have seen numerous of this style and the earlier style shear right off at the top of the knuckle....



If I was running hy-steer on a Toyota knuckle, I would run the ARP stud kits. I have installed them on a few trucks around here, and will be ordering more as I only have one set left on the shelf.



:beer:
 
Here is an interesting question. COuld you drill and tap the smaller knuckle bolts for a larger stud?

Do the knuckles with the larger studs have any other differences than the ones with the smaller studs?
 
Just got home and measured the pattern on my 71 FJ40. I have the large bolt pattern!!!! :doh: I will call Luke tomorrow and look into those ARP studs. I know about all the components on my FJ55 except the front axle. I was under the impression that I had early axles with a MAF front disk conversion...........I guess it is a later model with what looks like Toyota disks. I have dirtied my hands on everything except the front axle.........I guess I will see when I put on my new goodies. :flipoff2::grinpimp:
 
Back
Top Bottom