sm465 setup - adapter - 3 spd

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 11, 2005
Threads
159
Messages
1,910
Location
Sunny South
i am currently putting together a 350-sm465-3 spd t-case, i got all those but didn't order woody's adapter plate yet. I'm having one hell of a time trying to find a machine shop to drill/tap the out put shaft. they all said its nearly impossible to do, 3 shops said they wouldn't touch it. I explained that it had been done and still nothing. I'm running out of ideas. I could get a stud TIG welded on there but would they still be able to get it perfectly aligned? and i prob have the same amount of luck.... thanks...all
 
its a bit harder to coax the shop to do it then it sounds... even if i had 3 dozen donuts....

if woody or someone could chime in it would help a bit more... how deep does it need to be drilled/tapped or how long of a stud needs to be welded to the output shaft and where do i find a thick washer like you have..i don't have any "connections" to machine shops so its hard to find somebody to do this
 
I was lucky in that I had a friend do it for me who had access to a lathe. I assume you have the main shaft out of the tranny? If not I don't know anyone that would attempt it or get it straight. You could try it yourself but I would not recommend it because my friend had a tough time getting through the hardened metal. You could contact classic cruisers in Salida, Co. They sell a main shaft already tapped and has a spacer on it to keep the Tcase gear from sliding in too far. It was quite a few years ago when I spoke with them about it but I believe it was around 150.00 bucks. VERY IMPORTANT!!!!! Make sure that you saftey wire the bolt that holds the Tcase gear on. I have had one friend that had it come loose and it drops the gear into the bottom of the Tcase and has to be disassembled to put it back on. Locktite is not enough. Good luck Tom
 
Also if you have an older ( steel top ) 465 make sure the countershaft has been updated with the spacer that replaces the two snaprings. It really really sucks to pull that heavy pig back out after you find it won't shift nice.
 
nailbender said:
Also if you have an older ( steel top ) 465 make sure the countershaft has been updated with the spacer that replaces the two snaprings. It really really sucks to pull that heavy pig back out after you find it won't shift nice.


i know what ya mean , that is exactly what happened in my install 2 weeks after completed. the tranny chewed up a c-clip . replaced it with the spacer . got away lucky no visible damage to the tranny , that i know of . been 3 yrs since the install .
 
I had a connection at a shop in Appleton that did it for me.....buddy now owns a "block" nearby that includes a bar, and I'm headed there shortly.

They did mine with the shaft in the tranny....mounted it on a lathe deck and had at it....they DID junk a bit or two tho.....

tig welding a stud on "shouldn't" be that tuff....it only needs to be long enuf to allow for a nut/washer on it....the local True Value had a workable washer, and frankly, the stud allows for safety wire and is IMO a better solution.

Any welder with his melon screwed on straight outta be able to get it straight....it needs to hold the gear on, not align the universe.... ;)
 
I don't see why they wouldn't do it. I work at a machine/pump shop and we do way more complex things. I have had to do similar things to stainless pump shaft without any problems. I would just keep looking for a machine shop or a guy who does it on the side.
 
bandy rooster said:
i'd screw it up for sure... if i tried to drill/tap it myself

Hey,at least he's honest. Try the little two man machine shops first,i cant see them turnin down a couple bucks,Good luck
 
its not out of the tranny, i tried to bargain with the guy saying the only the exterior part of the shaft is hardened. i'll try to search around for more shops - but i live in PA not to many choices and no one would even go the extra " foot " to help a guy out. i've never re-built a tranny or taken one apart but i guess i only have so many options with the root i want to take.
 
A lot of these machinist guys may not want to fool with it in the tranny because it is heavy and they would spend more time setting it up to drill on their mill or drill press than it would take to drill and tap in in a lathe. They still wouldn't be happy if they did because they would fret about the hole being completely straight and true. They have stong opinions about the right way and the wrong way and they only want to do it their way.

You just need to find a shop that is a little hungrier for work.
 
PM Junk and see if he will lend a hand. Buggerville, NJ isn't too far from you...he has a lathe and mill (but not neccessarily the skills to use them ;) ) He can call me and I'll talk him through it if needed.

You might also try OK4WD in Stewardsville, NJ. One of the counter guys is a Cruiserhead. Call and ask for Chuck. Their shop might be able to do it or at least send it to the shop they use for you.

Nick Jennings
 
Picked my sm465 up from a local shop here and he did it while assembled for nothing, no heat was used and he said it was actually pretty simple. Mentioned that the toughest part was aligning the transmission in the press.
 
I had Bruce drill mine at his shop. The shaft was still in the tranny so we bolted the tranny to the table. We heated mine just enough to get the bit to bite and only on the very end. I would guess the hardened metal is about 1/16 - 1/8th" thick.

http://www.root45.com/SM465Orion/
Sm465Gear2.webp
 
i guess my only option is to continue to call around for the right/willing machine shop to get it done. i have jeff dozier looking around to for some shops in PA. thanks for the replys but for now i guess i'll just sit on it. My engine mounts are comming in from AA so my V8 has a place to sit. anybody know a clutch kit number for the 350-sm465 that there using? I hope woody still manufactures the adapter plate for a little longer
 
What year 350 are you using? What flywheel do you have? There are at least 2 different clutches an 11" and a 12". Need to know the flywheel to know which clutch.

On my truck I had a '89 350 with a large flywheel. I used a parts store heavy duty clutch for a '89 Chevy pickup. Ran it 30K miles and parted the Cruiser. The clutch still looks new. When the 350 goes back into my current Cruiser the old clutch is going in with it. IMHO you don't need a fancy clutch (like Centerforce) with the combo you're using.

HTH,
Nick
 
Back
Top Bottom