Slee wiring harness....

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Ghostrider I

I wear many "heads" as I have many vehicles.
Joined
Jul 4, 2017
Threads
153
Messages
1,147
Location
Charlotte NC
Any opinions? Good or bad are welcome. I am planning on getting two, the regular headlight one as I am upgrading to LED 6000K bulbs, along with the one that allows for "plug and play" for auxillary lighting.

Cheers!!
 
My first thought when I unpackaged my Slee headlight harness was “cheesie relays” but in two years I’ve had no problems with it.
 
I just put my second setup into my new 80 and while the relays are not top notch the last setup worked great and is to this day best I know...
 
Forget the harness.
Poor relays, cheap wire and bad crimps. Mine was nothing but trouble.
Ditched it and back to having reliable lights.
 
Supposed to allow more current to the headlights and in turn your supposed to 'get the most of your lighting potential or bulb upgrade' or something to that effect.
Replace those old worn out stock wires!
I had nothing but trouble

The there is the auxiliary harness for...you guessed it.
 
Thanks dude. Mine is stock wiring with HIR lamps. Works just fine..:)
 
The harness uses the stock wiring to trigger the relays which direct power straight from the battery to your headlights.
 
The harness uses the stock wiring to trigger the relays which direct power straight from the battery to your headlights.

Isn't that exactly what the stock system does? Has anyone actually measured the voltage between the two setups to see how much extra is delivered thru the aftermarket harness?
 
Isn't that exactly what the stock system does? Has anyone actually measured the voltage between the two setups to see how much extra is delivered thru the aftermarket harness?
According to the 1994 fsm wire diagram, that is correct. I have not compared voltage outputs beforeand after the Slee Barnes’s install and am unable to offer a comparison of light output because I also installed depo headlights with h1 and h4 bulbs the same day. I can tell you that ever since that day, I can see what’s in front of me driving on dark country roads a lot better.

Perhaps the main idea Of the Slee harness is to eliminate the possibility of increased resistance of older wires. Measuring voltage at the light sockets as a direct comparison sounds like a great idea.
 
^ why would a new harness improve LED output?

LED's will draw less current than incan and they will have driver electronics to regulate current. So whether they have 14V, 13V, 12V should make no difference since the driver topology would be chosen for the LEDs in use to ensure they are in full regulation from likely 10V to the maximum input rating. Certainly a decently designed driver would do that.

cheers,
george.
 
I've read the old harness was higher quality. Hard to believe there is that much voltage drop across the OEM harness, but I never did a side by side comparison. I take your word for it being better though. I use the 9011 bulbs in stock housings. That was a big improvement.
The cool harness was an impulse by for me that I regretted. Especially when the lights were going on/off while on the highway at night.
As always....YMMV
 
My personal experience is that it caused unreliable low beam operation. Sometimes the driver would work, but not the passenger, sometimes vice versa, but hardly ever would both headlights work at the same time. The harness was installed by a PO and had been on the truck a really long time. Took it out and my headlights have been 100% reliable since. If you search the topic, there are a good number of people who have had trouble with these harnesses and remove them. Also a good number of people who like them. FWIW, i saw no difference in brightness (other than the headlights actually working!) when I removed mine.
 
On some cars the aftermarket harness delivers significantly more voltage than stock. On the '80, we have measured a couple and the stock harness delivers the same or slightly more. Not sure how that would make more light? Our SOP is to remove them, the good news, they sell quickly!:hillbilly:
 
Stock with HIR after ditching the main Slee harness. It dropped high beam.

I've used their auxiliary circuit for five years with no issues.
 
Back
Top Bottom