Should I try this job?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 4, 2005
Threads
7
Messages
68
Location
columbia, sc
This is my first post and am doing a body of restoration to my 75 FJ40. I about have the body off and ready to start on the frame and the axles. It is wet behind the wheel assemblies and I think they need to be redone. I am debating whether to tackle this job or leave it to someone else. I have the haynes manual and read it, but I want it to be right. Can a first timer do this rebuild job properly?
 
Just Keep Reading

read untill you cant read no more.then just go for it, once you get into it it's not that hard. i was sceptical about going into my front end untill i did it, wasnt as bad or as hard as i thought it would be.
 
The only way to learn is to read, read, and do it, Find some one close who has the knowledge you might not have and buy him/her some beer for the knowledge.

Also Buy my 7/75 axles so you have some spares:))))
 
Around here "wet behind the wheel assemblies" means my dog pissed on the tire.

With the information given I'd say its likey not a job you can handle.

If you come back with "there seems to be some brake fluid weeping from the wheel cylendars" you may instill a bit more confidence.

Get brave newbie, Cruisers are simple machines and the internet is full of good info on how to keep them alive.

Good Luck
 
The only way I've learned jack about wrenching is to dig in and just do it. I usuallly invite over my bud who is a pretty experienced mechanic to provide some guidance when the going gets tough. :cheers:
 
Everything is easier once you get started into it - might as well get your hands dirty - the hardest part is trying to get frozen bolts loose and everything cleaned up prior to re-installation.

source some disc brake parts - bearings and seal kits - new brake hoses - TRE's - plenty of shop rags and degreaser/brake kleen and go to it - lots of good write ups with pics on here in tech section

so easy one guy even does it wearing sandals - guess he's not in an OSHA workplace :D
 
Chase77 said:
The only way I've learned jack about wrenching is to dig in and just do it. I usuallly invite over my bud who is a pretty experienced mechanic to provide some guidance when the going gets tough. :cheers:

I totally agree. You have to start somewhere. Just take your time and have fun wrenching.

Just ask questions or search on here and you will be good. :cheers: :bounce:
 
true, it always seems or sounds like it is harder than it really is. best way to learn is to tear into have a beer or two and enjoy yourself.
 
If it's not your daily driver then go for it.

If it takes a little long than expected, no worries.
 
yup,gear oil

mikesc said:
I guess that I should have said that there appears to be diff oil all around under the steering knuckle. I am new at this, but I will learn to provide more clear discriptions.
get yourself a knuckle rebuilt kit,it will [should] have everything you need to do it right.make sure you have the inner axle seals,thats why your getting gear lube at the knuckles.you'll need LOTS of rags and brake cleaner to clean it up.start by cleaning and scraping off all the dirt and gunk on the outside of the knuckles.THEN GO FOR IT!!!! ;)
 
it's especially easy to do something like this when the truck you're working on is not your daily driver. since you're doing a body-off, you have nothing but time to do this job so you might as well dig into it and learn about it as you go, its not like you have to have it back together by monday to get to work :cheers:
 
Don't take apart both sides at the same time, and try to find a clear picture of the placing of each of the seals and retaining rings.

Very gooey but not difficult. Get about three pounds of good grease and lots of paper towels.
 
I about have the body off and ready to start on the frame and the axles. It is wet behind the wheel assemblies and I think they need to be redone. I am debating whether to tackle this job or leave it to someone else.

Messy, but not especially hard. Especially if you've managed to get the body off. Suggested reading: Jeff Zepp's disc brake/front axle write-up at http://www.rzeppa.org/resto/resto18.htm et seq. Specter has a nice front axle manual too.
 
Everyone has a first time at doing a knuckle rebuild. Dig in and git-r-done. There's a lot of info on the net as well as in the factory service manual. A bit messy but not hard.
 
That's what great about this forum, dig in, if you get stuck somewhere along the way come here and ask. There's a ton of knowledge here and everybody is willing to assist. Dig in...........oh ya and warm newbie welcome :flipoff2: :flipoff2:
 
:banana: :banana: , really not difficult at all. I'm still quite new to the world of mechanics. This rebuild sounded difficult to me when I read about it, but is amazingly simple. Since you will be fixing seals and knuckle rebuild kits come with trunion bearings, you should replace those at the same time. Without knowing what you are doing, it should be possible to do this in a long day with many beers, tub o' cv joint grease, torque wrench, fishing scale. and more beer.
 
nice mike...

where abts in cola are you?
you should head up to clemson sometime when you get the 40 done and wheel it with some of us upstate guys...

got any pics of the progress on the rig?



malphrus
 
That sounds like a good idea to me. I am in irmo. I have some pictures when I first brought it home and need to get some more. The body is stripped down and I am getting ready to cut the tub off. Then I can start on the chassis.
 
Back
Top Bottom