Shifting into 4low

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 3, 2006
Threads
17
Messages
84
Location
Vancouver, BC, Canada.
Website
www.paool.com
I recently purchased my first cruiser (78 FJ40) a few weeks back, and i've been trying to get it up to spec for safety and insurance reasons. I'm not REALLY new to 4wd vehicles, and I'm not that new to cruisers either, but I've never been much of a mechanic. I can handle easier things, and I understand most of the lingo.

With that being said, I cannot get this thing to shift into 4low, for the life of me. It goes into 2h and 4h just fine, The hubs all lock in, and it seems to work just fine in 4h. But I've tried everything to get it in 4low, nothing works. I've tried Rocking it, Clutch in, clutch out, Nuetral, in gear (clutch in + stopped), hubs unclocked/locked, back up a few feet try again.. etc etc.. Everything... But the damn T-case shifter wont budge to the right. I contacted the PO about it, and he said its been stiff for quite some time, but thats all he ever really used on the trails so it should be working fine... It was working when he sold it to me, he says anyway.


What could be the problem? Low fluid? Buggered T-case?... Keep in mind 4h works just fine and engages with hardly any resistance.

P.S. Search didn't reveal any Usefull info for me, so Don't say I didn't look :D
 
My 74 is the same way. I haven't had time to mess with it much and can't offer any help but can say it must be somewhat common.
Good luck
 
Possibly a linkage problem or adjustment. I'd go underneath to disconnect the rod that goes to the top of the T/C so the lever could be worked manually. If you get three positions when shifting that one by hand then it's got to be a problem with the linkage. It's the one that requires reaching over the top of the t/c and is usually not visible from underneath. You have to feel it.

The 2wd to 4wd shift is done by a different rod than the one that ggives the choice of hi - nuet- low


This isn't an uncommon problem. Search will bring up plenty of detailed repairs.
 
Thanks. I know I'll be giving that a whirl soon. The stick really flops around so your probably right about the linkage.
Thanks
 
It took me about a week to get mine in low. Once I got it, it's been getting easier and easier. The PO of mine must not have s***ed in low in a long time.
 
I like the linkage on the earlier floor shifters. The ones where the arm on the transfer case points to the right side instead of the torwards the front. Alot more positive shift. This is the setup with the post mounted on the 4WD box that the HI/LO shifter pivots on. This came on the three speeds and some four speeds.


John
 
My '78 did the same thing when I bought it. I was worried about the T case but the linkage was just frozen. A little PB Blaster applied to the pivot points and a few easy taps with a hammer on the end of the sift lever, and I was low range enabled.
 
My 69 did the same thing. I pulled the case out and it turned out to be a small amount of galling on the shift fork shaft. Not sure why this happend as there was plenty of fulid. I pulled the shaft out and took a fine stone to it and that fixed the problem.
 
bad thing

Living in the Past said:
I like the linkage on the earlier floor shifters. The ones where the arm on the transfer case points to the right side instead of the torwards the front. Alot more positive shift. This is the setup with the post mounted on the 4WD box that the HI/LO shifter pivots on. This came on the three speeds and some four speeds.


John
One bad thing about having 4 Low way over to the right is the passenger can easily knock it into neutral with their leg. I have had that happen to me several times. A couple of times it was when I was climbing Kilimanjaro! I love rocketing down the hill backwards!. My passengers are educated in this and I usually have them wrap their leg around the lever.
 
I, too, shall from now on educate my (female) passengers that they must wrap their leg around the lever...


Colorado Boy-74-FJ40 said:
<snip> My passengers are educated in this and I usually have them wrap their leg around the lever.
 
quote:

Originally Posted by Colorado Boy -74-FJ40 One bad thing about having 4 Low way over to the right is the passenger can easily knock it into neutral with their leg. I have had that happen to me several times. A couple of times it was when I was climbing Kilimanjaro! I love rocketing down the hill backwards!. My passengers are educated in this and I usually have them wrap their leg around the lever.


I didn't think the lever went any further over on the early style than the later style. The shift pattern is the same. All the linkage that is different is below the transmission hump. If you bend the lever towards the center this helps the lever from being knot while in low range. I agree this is a problem it would have been nice if Toyota had installed a lock like they have for the PTO lever to keep it in low range. I like the thrill of rolling down a hill backwards with the original brakes in a 68. This happen to me years ago while teaching my oldest daughter how to drive. Try steering from the passenger's side while pulling the hand brake under the dash. I still don't know why we didn't hit one of the two trees at the bottom of the hill.:eek: In my case the low range was not fully locked into low range and just popped out. Another time I was flat towing my 68 and was sure the transfer was in neutral, turned out it was in low range. The transmission was in neutral so it didn't hurt anything but the oil smelled like natural gas. I had a neighbor call the gas company.:)


John
 
PabloCruise said:
Sorry, I was busting up laughing there...

Linkage needs to be cleaned and lubed.


Didn't relieze. Mad me laugh after reading it again.
 
I found a plug on the same side as my shifter on the transfer case was dripping lube oil. I took it off and sure enough looked like a fill plug. It had a copper washer so I cleaned it up and put it back on. Then I put lube oil in what I thought was the fill plug on the drivers side on the back of the transfer case. The one with the copper washer is lower than the fill plug. What is what?
 
WES1977 said:
I found a plug on the same side as my shifter on the transfer case was dripping lube oil. I took it off and sure enough looked like a fill plug. It had a copper washer so I cleaned it up and put it back on. Then I put lube oil in what I thought was the fill plug on the drivers side on the back of the transfer case. The one with the copper washer is lower than the fill plug. What is what?



This plug that you removed was on a housing bolted to the nose cone correct? The purpose of this is to create an access the bolt retaining the front drive engagement fork on the front drive engagement shaft.




Living in the Past said:
I like the linkage on the earlier floor shifters. The ones where the arm on the transfer case points to the right side instead of the torwards the front. Alot more positive shift. This is the setup with the post mounted on the 4WD box that the HI/LO shifter pivots on. This came on the three speeds and some four speeds.


John



John,


You must be one of the only ones that prefer that set up. There are so many more locations for wear to occur and create slop and that fantastic vibrating noise. The later four speed transfer case controls have always been quieter, as they have nylon bushings on the pivot shaft, and have not once given me or others that I run with any trouble. Just like any of the shifter linkages, if they are not properly lubricated, will become difficult to manipulate.




:beer:
 
I guess I like the old ones because of the leverage of the old shifters. If you have a transfer case out of a vehicle install the short rod that connects to the end of hi/lo shifter lever. Now with your hand try and move it in and out of high/low range with is straight off the lever like it is in the later shifer it is alot harder to shift than it is when the rod is 90 degees to the lever like in the earlier shifters. I like the way the way the lever is pushed and pulled from the side instead of being draged back and forth off the end of the lever like on the new ones. I personally feel it's a more postive shift but that's just me. I agree there alot more parts and the things do vibrate more, alot more. But I never came across one that I couldn't get the shifter to work.


:beer:




John
 
Back
Top Bottom