She's Mine!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Check into a set of Gorilla or McGard nuts , they are both very high nickel content and will not rust , look nice and have very well cut threads . Use a bit of anti-seize and they are good for a lifetime . Most times it's an issue with the existing stud threads being pulled or distorted from people using impact guns and stretching the studs , not the new nuts . I have ran across some cheaper nuts made who-knows-where (maybe China) that the threads are not cut properly .... if they don't go at least half way down by hand something is wrong .
Sarge
 
Check into a set of Gorilla or McGard nuts , they are both very high nickel content and will not rust , look nice and have very well cut threads . Use a bit of anti-seize and they are good for a lifetime . Most times it's an issue with the existing stud threads being pulled or distorted from people using impact guns and stretching the studs , not the new nuts . I have ran across some cheaper nuts made who-knows-where (maybe China) that the threads are not cut properly .... if they don't go at least half way down by hand something is wrong .
Sarge

Thanks for the reco Sarge...I'll take a look at them (had thought about just going back to the acorns, but I like having the closed nut.

Think I'll also end up changing out all of the studs (at the very least on the rear)....anyone have a recommendation on a good stud to go with? (OEM prices are crazy)...also, what is the correct size and length?
 
Lookin Great M Nelson.coming along nicely. What you decide on the hubcaps? You gonna run with or without?
 
I like to use the factory black acorn lug nuts from the '81-'84 40 series and 60 series. They fit really well and keep water out of the threads.
 
X2 on TORFAB if you are looking for a place that can work on it I the Seattle area. I went on the Seattlecruiser site but don't see when the next meet will be. I would like to meet with some other -40 owners, I'm up in Mukilteo.
 
X2 on TORFAB if you are looking for a place that can work on it I the Seattle area. I went on the Seattlecruiser site but don't see when the next meet will be. I would like to meet with some other -40 owners, I'm up in Mukilteo.


I will definitely be bringing my rig to Torfab for anything out of my pay-grade. Everything I've seen changing the studs on the rear is rather simple. Front end is more involved as you have to disassemble to and pop the rotors off.
 
Well, after nearly 10 years Im seriously considering selling my FJ40. Truth is I've never gotten to use her like I wanted to - and it really looks like that's not going to change i\n the near future. It just makes me sad looking at her sitting in the garage not being used/enjoyed like she should be. I know MUD can sometimes be a notoriously tough place to sell....but thought I'd post it here to get people's thoughts. Little has changed on her since the last pics. Right now is sitting at 21K miles....so I've literally put 2K miles on her over the last 10 years....pathetic.

I've also accumulated a bunch of NOS parts including
new inner door cards
New front turn signal lights
New aisin locking hubs for knuckle rebuild.
New bezel in primer..hasn't been painted
NOS emblems
New clutch master and slave installed in the last two months
New brake master....just to have on hand.

Think a bunch of other parts I'd have to go through to document.

I'm the second owner of this...I had planned to use it a lot more than the first owner and failed miserably at it.

I realize it's not a trailer queen....but I like that it's still wearing its original paint...and the miles are insanely low. She starts up perfectly every time and runs beautifully.

I was thinking of asking $35K....does that sound right?
 
Well that ended abruptly

Nice, looking forward to the continued journey.
 
Well that ended abruptly

Nice, looking forward to the continued journey.

I’m a sucker for a patina truck. I just want a shot at that paint preservation.
 
I’m a sucker for a patina truck. I just want a shot at that paint preservation.
You sir, are a true gentleman. Thank you.
 
Back
Top Bottom