Shackle Reversal Kit Identification

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Drake2

SILVER Star
Joined
Oct 11, 2017
Threads
576
Messages
4,591
Location
SW Utah
I am trying to identify, if possible, the manufacturer of the shackle reversal kit on this rig. Was installed 2 PO's ago so I have no documentation on anything that was installed here (other than the Con-Ferr shackles and Skyjacker Softride springs). Also, I thought there were some SR kits that did not add lift and some SR kits also added lift, I could be wrong about this. I have tried looking at all the current suppliers but did not see anything identical. Keep in mind this kit was installed over 20 years ago.

Disclaimer: I have done nothing to this rig yet. All mods were done 2 PO's ago. The PO I bought it from did no mods. He bought it and it sat in his garage for like 18 years until I talked him into selling it to me. Now I have the task of going through it to fix all the f'ed up things there were done to it. Some people should not own tools much less a welder or torch.

Thanks for any input!

1547529819697.webp


1547529824896.webp


1547529825124.webp


1547529825299.webp


1547529825837.webp
 
Not a Man-a-fre unless it was bought there before 1997-ish. That design was originally from Advanced Handling.
Ross Stewart, I believe. was the owner. I redesigned the kit in the the mid 90's for better approach angles.
We used a hinged , flat ramp and a stock 40 with 31s as a test. We could elevate the ramp up to 45 degrees
and made test runs until something on the truck would drag. The first run, everything stock , except 31's, the shackle hit first.
The advanced handling hit the front bracket first but lost 5 degrees of approach over stock .
Our redesigned kit hit the bottom of the forward edge of the leaf first but not before gaining 11deg of approach.
With stock, the risk of inverting the shackle, or breaking it, was a possibility. With the advance Handing, the sharp forward edges
would catch and may stop you pretty quick on some rocks. With ours. sitting down on the leaf didn't really stop
forward motion much or prevent you from backing off. They were tested pretty extensively in the ARCA and BFG Rock Crawling event.
We put the reversal and u-bolt flip kits on Don Robbins and my 40 while Tracy Jordan and Rob Bonney drove their 40 with
the same parts. Out of all the parts failures in three years neither of those were a problem
The other issue with the original was the rear mount. The rear was symmetrical front to back. If you ran a stock shackle
the rear eyelet of the spring would swing back and hit the bracket preventing full compression without binding the leaves.
Our bracket had the material removed on the back end allowing the shackle to swing up to the frame.

I stopped building these as a wholesale item after the crash but passed the parts on to Man-a-Fre LV. As far as I know they still
build this style. I've also seen Ross's version knocked off by a couple companies over the years .

IMG_3080 (2).webp


IMG_5473.webp


IMG_7265.webp
 
Before someone asks... why does the front bracket hang so low?. Correct leaf spring geometry should have the spring eyelets as
close to level with the horizon as possible to get neutral steering. Raising one eyelet or the other affects understeer and oversteer.
Because of the downward slope at the rear of the spring , the front bracket should actually be even taller to get correct geometry.
Like all things modified we chose a compromise. Our resulting setup leaves the truck with a -2 deg caster so a 4 deg caster shim
is used to return the truck to a +2. The alternative was to make the bracket 4 inches taller, thus a compromise. The bracket
really only drops about 1/2" more than the original shackle and hanger assembly but the visual perception is that it's huge.
We spin the leaf front to back. The 40 leaf has a off center split. Normally the short side is back and the long side forward.
By reversing the spring, the short side forward, we can rake the front bracket backward bringing the first contact point
closer to the tire so even though the bracket is a 1/2" taller the approach angle improves.
This improvement is even more noticeable as tires get bigger.
 
Last edited:
Before someone asks... why does the front bracket hang so low?. Correct leaf spring geometry should have the spring eyelets as
close to level with the horizon as possible to get neutral steering. Raising one eyelet or the other affects understeer and oversteer.
Because of the downward slope at the rear of the spring , the front bracket should actually be even taller to get correct geometry.
Like all things modified we chose a compromise. Our resulting setup leaves the truck with a -2 deg caster so a 4 deg caster shim
is used to return the truck to a +2. The alternative was to make the bracket 4 inches taller, thus a compromise. The bracket
really only drops about 1/2" more than the original shackle and hanger assembly but the visual perception is that it's huge.
We spin the leaf front to back. The 40 leaf has a off center split. Normally the short side is back and the long side forward.
By reversing the spring, the short side forward, we can rake the front bracket backward bringing the first contact point
closer to the tire so even though the bracket is a 1/2" taller the approach angle improves.
This improvement is even more noticeable as tires get bigger.
Thanks to all for the input. Let's me check one more thing off on the never ending to-do list!
 
Thanks to all for the input. Let's me check one more thing off on the never ending to-do list!
Don't get me wrong, I prefer the shackle reversal but there's so many ways to do it wrong unless you pair a kit with a specific manufacturer's
spring you can't be 100% sure of the outcome. The kit we had worked well enough with the Standen Springs that Man-a-Fre sold. I saw no
real issues with OME either. The relationship between the flat in the middle and the two spring eyes determines caster on a 40. There are a couple out there that are seriously off factory spec. I believe it was a Rough Country that I installed that needed 10 deg of caster adjustment.
A shim that size has to be welded to the perch. The better option was to cut and turn the ends.
For me and the wheeling I do a shackle reversal on my 40s , 55s and 60s was essential. I've broken shackles on all models and torn the
front shackle hangers off every 60 I've owned. The latter being the fault of Toyota, in my opinion. The shackle hangers on the front of the 60
are poorly attached....check one out up close. I think they had a Jeep engineer do that single piece.
The slips on a 40 series driveshaft are only about 2 3/4". By comparison a 60 has about 3 1/4" . This isn't an issue when the axle swings toward
the t-case in droop. When you shackle reverse a 40 , the axle swings away. The the more travel you have, the longer the slip needs to be.
The 80 series front has a 6" slip with a yoke that allows 45 deg articulation where the 40 and 60 only allow 24~27 degrees. The 80 driveshaft
tube is the same diameter as the 40 and 60 so the slip assembly can be welded into either driveshaft. This swap get rid of the possible
driveshaft separation in droop and allows you to place the high angle yoke at the most vulnerable point, tcase or axle, depending on
what your setup is. This should be at least looked at and considered on four inch and over lifts.
 
There is a massive amount of serious info in this short thread. Wow.
 
There is a massive amount of serious info in this short thread. Wow.

I know how much it sucks to do things twice. I made lots of mistakes the first ten years I owned a 40. I bought the first 40 when I was 18.
I did three v-8 swaps, three suspension changes and two P/S conversion in the next ten years til I was really happy with the truck.
Done right they 40 actually handles great. I had kept a copy of the speeding ticket for years as a trophy. 108mph on I-17 . The police had better a sense of humor in 85 and there was no felony speeding tickets back then...just speeding.
 
I know how much it sucks to do things twice. I made lots of mistakes the first ten years I owned a 40. I bought the first 40 when I was 18.
I did three v-8 swaps, three suspension changes and two P/S conversion in the next ten years til I was really happy with the truck.
Done right they 40 actually handles great. I had kept a copy of the speeding ticket for years as a trophy. 108mph on I-17 . The police had better a sense of humor in 85 and there was no felony speeding tickets back then...just speeding.


And here I just try to keep the mighty 2F at 55! At least I rock a cool front grill and a cooler/tire carrier!!!

Now I need to score a nice roof rack....
AD2A01FD-5B4C-4BE6-B166-AD23A1D6C49A.webp
 
Back
Top Bottom