seat swap?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 6, 2014
Threads
6
Messages
33
Location
Woodacre, CA
My seats in my 94 are tired. They are the less cushy manual ones and I don't think they're comfortable enough to shell out the cash to rebuild them. There are a few seats from other vehicles on my local CL that are cheap ...

What seats from other models can fit in their place? Will Toyota seats from other models in this era work? What about seats from a Lexus RX? Mid-eighties Toyota pickups?
 
Anything is possible with work just depends on your mechanical aptitude and time.


...via IH8MUD app
 
I once put seats from an early 90's Mazda into my '72 Blazer. Almost anything can be made to work as long as they're not too wide for the space.

I am in the same situation ('93, manual, cloth, uncomfortable) and I am curious what non 80/LC seats others have already installed in their 80's and if they're happy with the results.
 
Hopefully this gets some traction, I have always wanted to swap seats preferably ones with some arm rests and power adjustment. I would love to see if a adapter bracket can be made for a 2003+ Land Rover Discovery seat, there are always tons of them being parted out and the interiors are always immaculate and looks pretty cool too. I have seen them on CL for both fronts for $75, can't get decent seat covers for that much.
 
Hopefully this gets some traction, I have always wanted to swap seats preferably ones with some arm rests and power adjustment. I would love to see if a adapter bracket can be made for a 2003+ Land Rover Discovery seat, there are always tons of them being parted out and the interiors are always immaculate and looks pretty cool too. I have seen them on CL for both fronts for $75, can't get decent seat covers for that much.
I see lots Discoverys in the pick n pulls. I might measure the LC seats tonight and head to the pick n pull tomorrow and see if the DII and other model seats are close enough to pay the $40/seat charge to test out.
 
only seat i would consider for my lc is suspension seats for saftey first and then comfort. mastercraft and prp are my top choices
 
only seat i would consider for my lc is suspension seats for saftey first and then comfort. mastercraft and prp are my top choices
I had Mastercraft suspension seats in my Jeep Rubicon. I had the non reclining kind and they worked for me pretty good. I had 5 point harnesses installed. They were very comfortable to sit in but were not fun to get in and out of on a semi daily driver. No one will want to ride with you either. That could be a good thing or a bad thing. If you want to correctly install a harness you will need a bar that runs behind the seats for the seatbelt harness to mount to.
IMG_1376.webp
 
I went to the pick n pull today and did some searching. The LR Discovery seats look to be the same dimensions. Only thing I noticed that may be an issue would be the base. The seat motors aren't hidden like the LC. I almost bought a set but the seat switches were taken already. Another possible donor are seats from early 2000 Troopers. They are cloth, manual and have arm rests. They were very comfortable to sit in. The only clean seat I found were from a smokers car so I left them as well. So it wasn't a good day to pick something up to test fit.
Now I have to research seat covers. I wouldn't want mismatched seats in my LC. I know Escape Gear makes quality covers for LC's and LR's so at least you can make those match if needed. Don't know about Troopers.
 
Some of the finest seats to ever be put into a common production vehicle can be found in the BMW 7 series. I would love to see someone swap these into an 80. I would be more inclined to investigate, but my 1994 cloth/manuals are absolutely pristine!
 
Some of the finest seats to ever be put into a common production vehicle can be found in the BMW 7 series. I would love to see someone swap these into an 80. I would be more inclined to investigate, but my 1994 cloth/manuals are absolutely pristine!
I agree. It was always a pleasure riding in a co workers 7 series years ago. I sat in some Volvos today as well and I liked them and they seamed like they aged very well but they were all black.
 
If you are not going to a newer style and modern aftermarket seats then it doesn't make sense to change over to a seat from another vehicle of the same vintage. My suggestion is to rebuild the seats by swapping out the bottom and back foam cushions from Toyota. Unless of course, your body type is not compatible with the oem seats. I changed just the bottom cushion and it did wonders for me. Sitting higher due to the newer cushions allowed the lumbar to hit the lower back properly.

Just my .02 cents.
 
This may exist and I've overlooked it, but to this day I'm surprised that none of the major LC vendors have come out with an 80 series seat solution to allow easy fitment of an aftermarket or alternative vehicle seat. (IE: mounting bracket and wiring solution)

While there's a lot of threads about different seats people have run, aside from rebuilding the stock ones, I've yet to see something that looks like it's factory and is the obvious alternative to rebuilding the stockers.

Same seems true of the armrest. I rigged up a homemade one years ago and the $20 in parts made the truck so much nicer for long distance driving. Just seems (i could be wrong) like it'd be easy for a vendor to design something simple and do really well with the crowd here.
 
i put 90s mercededes seats up front in mine . i reversed them from right to left so i could use the reclining knob (pretty much a pain to recline slooow). the grey colour is close if your colour blind. the lumbar lever i disassembled because i swaped the seat bases for factory mounting. the seats seem identical to my ex's 05 passat. could be any german made seat might fit without being an engineer. didnt take long (short afternoon install) but be carefull with the seat bases they can bite your fingers when takeing them apart.
 
I went to the pick n pull today and did some searching......The only clean seat I found were from a smokers car so I left them as well. So it wasn't a good day to pick something up to test fit.

I think these two factors will be a major deterrent to me swapping.

If you are not going to a newer style and modern aftermarket seats then it doesn't make sense to change over to a seat from another vehicle of the same vintage. My suggestion is to rebuild the seats by swapping out the bottom and back foam cushions from Toyota. Unless of course, your body type is not compatible with the oem seats. I changed just the bottom cushion and it did wonders for me. Sitting higher due to the newer cushions allowed the lumbar to hit the lower back properly.

Just my .02 cents.

I see your point here and I'm glad you posted. I was wondering if my discomfort is due to the lack of lumbar support, or just due to the seats inherent ergonomics as it relates to my already damaged back (old injury, which mostly only affects me with bad ergonomics). Looking at my passenger seat, I really don't see any lumbar support per se, but I'm curious about your .02 so I will explore this further. Thanks again.
 
Somebody had a good write-up with vids and photos that used PT Cruiser seats. It seemed like a pretty easy retrofit compared to the ones where people have tried to use Land Rover Disco seats.
 
There are a couple good threads on this already. I think the best fit is the land rover disco seat. Close but not perfect fit.

Two problems fitting seats into the 80. The width but mostly the hight. The 80 seat is very low to the floor. Most seats sit you sevral inches too high. I am short so it was not a head room issue. But i didnt like the seating position sitting up so luch higher in the SAAB seats i put in. So i desided to continue working on rebuilding my OEM fronts.
 
Back
Top Bottom