Received FOR kit...kinda

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

if these are Frankie's bushings and you would like a free press template send me two of them. People have tried to use my Slee template but it doesn't come out right. I need two of these bushing to draw up the template.

Let me know

Thank you very much for the offer. Frankie sent me a template to use with the bushings. If it does not come out right then I might just press them out and send 'em to you.
 
Vista -

Get some pictures when you get it all put together and let us see how it comes out.

Cheers.

I might just get a couple of pics up with just the lift and no 315's. Gonna be getting the new BFG KM2's and it looks like those take about 4 weeks to get.
 
Pics :bounce:
 
Here is what FOR 3" kit looks like with Nitto 315's. It looks kind of small with the RTT on there. Frankie has been great to work with. Landtank is right about the template though. Try the one out that Frankie gave you (I used Landtank's). I'd feel more comfortable sending the bushings to Landtank and having him make you a free template though. I highly doubt there is anyone on the planet who understands 80 series alignment better than him.
If anyone needs any other info on the FOR kit, let me know. I advise against using the inside coil bumpstop spacers though. Lots of spring contact, I'll be ripping mine out soon. How did you install your shocks? Piston up or down?

241265531-L.jpg
 
Thank you very much for the offer. Frankie sent me a template to use with the bushings. If it does not come out right then I might just press them out and send 'em to you.

If his template aligns the holes so that one is at 12:00 and one at 6:00 I wouldn't use it.
 
How did you install your shocks? Piston up or down?

241265531-L.jpg

Piston down in the front, piston up in the rear. The rear is shock body down because it's a pretty vulnerable mount point. Don't believe it matters at all with the Bilsteins.

Your rig looks good - perfectly level on 315's. :clap:
 
If his template aligns the holes so that one is at 12:00 and one at 6:00 I wouldn't use it.

I will have to look at the template to see what it looks like. What is the issue with aligning them at 12 and 6?

Piston down in the front, piston up in the rear. The rear is shock body down because it's a pretty vulnerable mount point. Don't believe it matters at all with the Bilsteins.

Your rig looks good - perfectly level on 315's. :clap:

I mounted them with piston down on all 4 corners
 
I will have to look at the template to see what it looks like. What is the issue with aligning them at 12 and 6?

the end result will yield holes that are too far apart so the rubber is stressed some when installed on the axle. This also lessens the effect on caster and shortens their life.

With the templates I designed the axle is also rotated on it's center instead of tilting it on the bolts. This effects drive line angles less.
 
the end result will yield holes that are too far apart so the rubber is stressed some when installed on the axle. This also lessens the effect on caster and shortens their life.

With the templates I designed the axle is also rotated on it's center instead of tilting it on the bolts. This effects drive line angles less.

Interesting...always so much to learn. Are each set of bushings different? Is that why I can't purchase one of your templates for the OME or Slee bushings?

Here is the template I received from Frankie:


I can send you a set so that you can make a new template for the bushings Frankie uses if you think the above template is not a good way to go. Obviously I will pay for shipping both ways.

I drove it yesterday to see how it drives. The springs feel great and the truck has much less body lean than stock even though it is higher. The ride is firm but not stiff. I get a little grrrrr from the drivetrain but not nearly as much as a friend (Darwalk) got with his 5" OME Comp kit. I noticed that most of the vibration was between 20-30 and not really there at 60+.

-Garry
 
If you look at the diagram you need to be sure you maintain that 185mm distance between the two holes with a tolerance of +/- .3mm. This is pretty hard to do on both arms and have them the same. Any difference between the two arms will cause stress on the bushings and diminish their effect.

Now that I see how these are made they have a different offset than Slee's and that is why that template won't work for them.
 
If you look at the diagram you need to be sure you maintain that 185mm distance between the two holes with a tolerance of +/- .3mm. This is pretty hard to do on both arms and have them the same. Any difference between the two arms will cause stress on the bushings and diminish their effect.

Now that I see how these are made they have a different offset than Slee's and that is why that template won't work for them.

Nice......+/- .3mm tolerance. That should not be difficult at all. :rolleyes:
 
grab the rear slip yoke at the joint but on the rear section at the beginning close to the t-case and try and move it up and down. Your looking to feel some play in the shaft as if it;s bending in the middle. If it feels tight move your hand down the shaft away from the T-case and check again. Each move should be only a 1/4" or so. Do this for the first 8". I think you will find one spot in particular that reveals quite a bit of play.
 
grab the rear slip yoke at the joint but on the rear section at the beginning close to the t-case and try and move it up and down. Your looking to feel some play in the shaft as if it;s bending in the middle. If it feels tight move your hand down the shaft away from the T-case and check again. Each move should be only a 1/4" or so. Do this for the first 8". I think you will find one spot in particular that reveals quite a bit of play.

...and if I do feel some play? How much is "OK"?
 
there should be zero play in that joint.

Well...there is no play on the rear or front drive shafts. The vibration (grrrrrrr) is very slight but is there.
 
Back
Top Bottom