rear end - big problem

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 11, 2005
Threads
159
Messages
1,910
Location
Sunny South
i had recently bought this 40 and the previous owner had bought it not knowing anything about wheeling, just bought it to "have fun" well anyway when i bought it, he had nothing to tell me about it, he couldn't answer specific questions and didn't even know what power steering was...all the work was done by the owner before him

i opened up the rear to peak and see if it had a locker and what do i see ...welded spider gears, and i was sorta pissed but then i ran my hand inside along the wall near the bottom and found chunks of what apears to be welded spider gear or just welds that broke off of it, i cleaned it out best i could but what do i do know? is it drivable? can i grind out the welds on the spider gears? ideally i'd like to get a locker to replace it completly but i'm b-r-o-k-e... thanks any input would help, i can get pic's if you want them to help explain it :mad: :mad:

i'm scared to look in the front axle ...this may get expensive which means my cruiser won't see the road foreverrr...
 
Is it still welded up?

Nothing wrong with a Lincoln Locker (named after the welder) - lotso people do them!

Just pull the chunks out...

You can prob find gears in the FS section - good luck!

Does the pinion seal leak?

Does the pinion wobble at all?
 
There are quite a few people here who swear by welded spiders. It is not the end of the world if your final goal is a locker. Cheap lockers do the same thing as a welded set of spiders. Like stated above, you are now set with welded spiders unless you get a new third or can dremmel for a few weeks. Take a look at it and clean it up and go with it until you have 50bucks for a new third(free with good friends) and then 220-250 for a cheap locker. Try replacing the drain plug with a magnetic one to collect the metal pieces. Good luck, Eric
 
i'd have to get a high powered magnet to collect these, there like dime sized almost.... and its still welded pretty good i think.., no damage done to gears that i can see...it feels weird though i think there stock gears but theres like noooo play in it, like it isn't in stock spec on the backlash, i think its called backlash but if you guys say a lincoln locker is ok i'll just go with it ... its gonna be a daily driver but i'll get use to it, thanks for the feedback
 
bcon said:
There are quite a few people here who swear by welded spiders. It is not the end of the world if your final goal is a locker. Cheap lockers do the same thing as a welded set of spiders. Like stated above, you are now set with welded spiders unless you get a new third or can dremmel for a few weeks. Take a look at it and clean it up and go with it until you have 50bucks for a new third(free with good friends) and then 220-250 for a cheap locker. Try replacing the drain plug with a magnetic one to collect the metal pieces. Good luck, Eric

Um...

If nothing else is damaged you should be able to just replace the gears. I guess it would be a pain to get the side gears out, being that they are all welded, but I'd guess that if you pulled the pin, rotated the spiders away and cut it with a torch you could set em free and pull em out. Or like bcon said, pick up a new 3rd.

Depends on what all is welded on your particular rear. These pics show a couple different ways. With the one, your carrier is basically history. With the other it might be salvageable. (Thanks Woody ;) )
weld_008.webp
weld_002.webp
 
bandy rooster said:
i'd have to get a high powered magnet to collect these, there like dime sized almost.... and its still welded pretty good i think.., no damage done to gears that i can see...it feels weird though i think there stock gears but theres like noooo play in it, like it isn't in stock spec on the backlash, i think its called backlash but if you guys say a lincoln locker is ok i'll just go with it ... its gonna be a daily driver but i'll get use to it, thanks for the feedback


It will work...until it fails....just like anything.


Hopefully you are not going down the road really fast when it lets go...could get messy...


wear your seatbelt! :)



good luck!


-Steve
 
My bro welded up his front and it blew out, took some chunks out of the spiders but he wheeled it for a while like that before he threw in 4:11s. Run it till it blows like Steve said. Had the rearend lock up in my Dad's 60 on me at about 40 mph not too scary, just like yankin' the e-brake. Tell yo' dad to get you a phone w/ a camera & post some pics of it. I'd be stoked the rear's locked for now.
 
Off topic, I have the ebrake you needed dude. (Brandy) Where do you want me to send it????? PM me. Also I can throw in the box a used 3rd member for a few bucks. Dont worry about the truck sitting, Mines been in the garage for 4 years!
 
Back
Top Bottom