Real Time Help: Missing Rear Brake Pad

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 27, 2005
Threads
50
Messages
532
Location
Ugggggghhhh
I'm on a road trip and I have an issue with my passenger side rear brakes (97 LX). It appears the inside piston got stuck and wore the pad gone, ground down the backing plate till it fell off, and is now grinding the piston directly against the rotor and wearing that down. It grinds even when I'm not braking and everything in that area started getting real hot.

What's going to be the quickest, safe way for me to get back home (300 miles)? Once I get there I will be ordering all new rear brake stuff from cdan (rotors, calipers, pads).

Can I get away with just buying some new pads for one or both sides to get me home? I'm not going to find any Toyota dealers with the parts anywhere close, especially during the holiday. Its going to be napa or worse. What should I do???
 
I wouldn't drive it without new pads. Get the cheap ones, they'll be trash when you get home.
The most common cause for a sheared pad is seized mounting bolt. The caliper is supposed to float on the smooth part of the bolts and stay centered over the rotor. This allows the pads to apply equal pressure when the brakes are applied. If it seizes, you will wear out one pad quickly. Make sure you clean the bolts and apply some anti seize before putting it back together. Good luck.
 
Last edited:
crimp the hard brake line going to that caliper so the pistons wont play.drive slowly though. running on three brake calipers on a heavy rig is unstable but it will get you home if you drive safe enough
 
crimp the hard brake line going to that caliper so the pistons wont play.drive slowly though. running on three brake calipers on a heavy rig is unstable but it will get you home if you drive safe enough

What? This isn't a trailside repair in the middle of the jungle. Put on new pads and drive home. Replace what you need to replace when you get home and have time.
 
take a pair of vise grips and crimp the rubber soft line and tie wrap the vise grips to something so it dosent fall off . cheaper/easier to just replace the hose then having to fix the hard line when you get home
Yes this sounds like a trail fix , not cool but the OP is in middle of nowhere US do you think a NAPA or a FLAPs will have rear pads for a FZJ80 in stock let alone be open in the middle of flag waving USA on the forth of July weekend ? I cant get pads off the shelf here without them picking them up at the warehouse here between NYC and Philly on a weekday

Sometimes you got to do , what you got to do
 
Yep, nobody that's open has the pads. I'll try to pinch a soft line. Any way to back the piston off so it isn't constantly scraping the rotor?
 
where are you in your trip. That might help point to a solution

Any juink yards near you with crusiers. Get a used caliper, rotor and maybe even used pad.
 
Cody, Wy

The whole town is shut down for the 4th. No wrecking yards to speak of. I think I can just pinch the line, but I don't want to burn anything up with the piston grinding the whole time.
 
Cody, Wy

The whole town is shut down for the 4th. No wrecking yards to speak of. I think I can just pinch the line, but I don't want to burn anything up with the piston grinding the whole time.

If your going to pinch it, take off the caliper. Might try and find a fitting to plug the hole where the brake line connects to the caliper.

Guessing you at a minimum will need a new rotor if its grinding, maybe a rebuilt brake caliper or one from a junk yard.
 
Get a hotel room/stay an extra day, go to a movie, have a few beers, attack the problem tomorrow when everything is open again. Better/cheaper than having an accident, getting a 300 mile tow, or melting parts.
 
before you take off the caliper, might try prying open the caliper so its not rubbing and then pinch it to make sure it will stay that way. I use a big honking screwdriver or prybar between the rotor and pad/caliper

You should get it fixed before traveling across multiple states
 
take a pair of vise grips and crimp the rubber soft line and tie wrap the vise grips to something so it dosent fall off . cheaper/easier to just replace the hose then having to fix the hard line when you get home
Yes this sounds like a trail fix , not cool but the OP is in middle of nowhere US do you think a NAPA or a FLAPs will have rear pads for a FZJ80 in stock let alone be open in the middle of flag waving USA on the forth of July weekend ? I cant get pads off the shelf here without them picking them up at the warehouse here between NYC and Philly on a weekday

Sometimes you got to do , what you got to do

Good points Todd. Forgot about the 4th. Too busy prepping for CMCC and smoking ribs.

Either spend the night and attack in the morning or remove the caliper and shut off the line. I keep some old male and female brake line fittings for just such an occasion.
 
Got home safe. Thanks for all the advice. Taking off the caliper was the ticket. I did the work in an o'reliley's parking lot, the only parts store open. Bought a c-clamp to squeeze the caliper, and bought some super cheapo brake pads to jam into the caliper to hold the piston open. Taped it up real good and zip tied the crap out of it to the top of the axle. Couldn't even tell I was on three brakes, though I kept off them as much as I could, used the transmission to slow down as much as possible and kept the e-brake at the ready.

It looked like my pins were bent, and that probably caused binding and the inside pad to wear more. It wore down to the metal backing, where it was able to fall out. I found the metal piece stuck behind the cover plate. That's what was making the grinding noise while I was driving, which was very similar to the griding noise while braking, but for a totally different reason.

Tomorrow: Order some calipers, pins, pads, and rotors.

I'll post some pics of the carnage and fix later.
 
Glad you made it home.:cheers:

Look forward to seeing the pics, carnage is cool when it's someone else's.:hillbilly:
 
Bought a c-clamp to squeeze the caliper, and bought some super cheapo brake pads to jam into the caliper to hold the piston open.

Just ran across this thread, taking off the caliper and stuffing it with pieces of metal is absolutely the best way to limp home on three brakes (if no lines are leaking).

Driving on the freeway with a vice-grip on the hose when the caliper is removed is a TERRIBLE idea...what if the clamp loosens or leaks? All braking power in the half of the system will go to the backwoods "fix" line and you'll be down to two wheels, which is a lot less stable braking than three.
 
I lost a brake pad on a trail 3 weeks ago, caliper over-extended and started losing brake fluid- fast. Two vice-grips on the caliper soft line, mechanic's wired to the soft line, back on my way. Took about 5 minutes. I will replace the soft line when I fix the brakes. Original brake lines with almost 200K on them, I'll do 'em both.
 
This just happened to me. In Bullfrog Utah with wife, 3yr old, and u-haul trailer full of gear. No way I could drive anywhere like that. I removed the caliper and used the bleed valve on the caliper to plug the line to both rear brakes where it leaves of the rear brake proportioning valve. It fit perfectly. I only had front brakes, but it was a secure setup. We got back to SLC safely instead of being stuck in the desert for days...
 
Back
Top Bottom