real time carb tech

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 15, 2003
Threads
27
Messages
506
Location
Calgary
so here i am out in the garage, getting my laptop all dirty...

i'm disassembling my carb (75 aisan) so i can dip it until tomorrow night and hopefully have it all back together... as i unscrew the slow jets, i notice something wrong with one of them. a can only assume it was too long and it got forced in there? tell me it's supposed to look like this :crybaby:

what do i do?
IMG_2069s.webp
 
ok, i just read that there are 2 different sizes, and the longer one is for the secondary side... well that bent one came out of the primary side. anybody know how hard these are to come by? keep in mind i'm in Canada :flamingo:
 
DAMN! I've been rebuilding carbs for 20 years and have NEVER seen that one before! :eek: [where's that damn barf emoticon when you really need it.]

You are obviously going to need a new one of those. Call me at the shop tomorrow and I will drop one in an envelope for you, no charge.

That is just wrong.

Mark
 
65swb45 said:
DAMN! I've been rebuilding carbs for 20 years and have NEVER seen that one before! :eek: [where's that damn barf emoticon when you really need it.]

You are obviously going to need a new one of those. Call me at the shop tomorrow and I will drop one in an envelope for you, no charge.

That is just wrong.

Mark

Mark - Can't thank you enough! I'll check in the morning and see if my local guy has one, if not I'll phone you.

I'm also noticing now that i can't get the bowl separated from the base. If I'm doing this right, theres only one more screw in the bottom of the base coming up, but it's in there way too tight to get it out, especially with a slotted screw... whoever invented those should be shot. What's my plan of attack on this one? I can't dip it still attached - - - can I? I'm hoping I only have to have this thing apart once...

Furthermore, NONE of the little balls have come out of their channels/passageways, but I plan on blowing compressed air through this after I soak it. Does that sound feasible?

Again, thanks so much guys. :cheers:
 
If the slotted screw coming up from the throttle body isn't already stripped out, you can lay the carb on a rag over a piece of wood, upside down and put a long screwdriver with a square or hex shank down in the bore and try turning the screwdriver with a wrench while pushing down on the screwdriver REALLY HARD.

An impact driver with a long slotted tip works well too.

Every once in a while I still end up having to drill the head off of one that was boogered up before it got to me. That's why I keep spares on hand. :)
 
i tried that last night as a last ditch attempt, but didn't put too much effort into it... i'll try it again tomorrow with a little more gusto. although, i never thought to use a hex or robertson type driver.

i don't imagine you can get either of those parts (slow jet and the big screw) from toyota anymore? i'm weary of stripping that screw and not being able to get my hands on another.

in any event, i'll PM you with my address if the offer still stands for the slow jet, couldn't find one today and missed your 6pm closing time. again, thanks so much for the advice and offer!
 
There is a company in Canada that sells Keyster rebuild kits for the Aisan on e-bay for $25 plus shipping. Might look into that to replace the slow jet. The screw is not included in the kit.
-Brian
 
Be careful when ordering from Keyster.. Some of the kits come with jets and others only come with gaskets, o-rings, balls, and a new diaphragm. Make sure you find a supplier that can verify that it comes with jets. Also make sure they are the stock sizes. A buddy ordered a Keyster kit and got the wrong size jets with it.
 
i have a keyster kit, it didn't come with the jets.

my original plan was to send the kit away, either to Jim C. or Mark, but due to time constraints (and financial constraints) i decided to dig into it myself. if it gets any worse than this i'll just say :censor: it and send it away.
 
how did that jet being mangled effect how my truck ran? i never really had any problems with it, except a failure to pass emissions testing (running fairly rich) anybody care to explain to me what exactly these do?
 
Slo-jet is in the envelope ready to go. Let me know by morning if it's gonna cross paths with the carb, or I'll be dropping it in the mail on the way to breakfast.
 
ahh, mark, just the man i wanted to talk to. i ended up finding some slow jets today locally :cool: thanks a million for your offer, i definitely won't forget it.

i was getting close to just saying " :censor: it" , but i ended up getting it apart... tried a different screwdriver with a thicker tip, and put ALL my weight on it. everythings sitting in carb dip right now at the side of the house. it's hard to find a decent carb dip around here...

thanks again, i'll probably need everybody's help again getting it back together :doh: :cheers:
 
Back
Top Bottom