puking radiator

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 27, 2003
Threads
359
Messages
6,458
Location
Georgia Tech
This started about a week ago-

I crank the cruiser, and let it idle. After about 10 min of idling the cruiser it begins to drip coolant out of the overflow "hole" on the filler neck. The radiator feels very hot for just idling, but the temp guage is normal.

New radiator cap. (tried three).

No collapsed hoses.

I have no idea, other than possibly not burping the system completely last time I had the radiator out, but that was over 6 months ago.

Any help is greatly appreciated, as I leave for tellico in 4 hours. :D

:cheers:
 
Texican said:
Install an over flow jug and get the heck out of here.
Butch

I second. Your system sounds normal. You need an overflow jug.

If in a big crunch for time empty a soda bottle and cut a hole in the top for your overflow hose. Run the hose to the bottom of the bottle (so it can suck coolant back into the system when it cools) and zip tie it on. When you get home again fix it right.
 
Problem with this is that there is no nipple on the radiator for an overflow tube. Maybe 1/8".

Just took it for another spin and it didn't do it too bad.

Thanks guys, I'll work on getting a good overflow bottle when I get home.
 
different rad cap, IIRC the earlier f's were'nt designed to have an expansion tank system.
one cap has two sets of rubber gaskets, the other only one gasket.
 
No surge tank, you have to leave the coolant level down an inch or so to allow for expansion, or it will puke it out and clearance itself.
Butch
 
it will set its level automatically. Heat it up and it will dump what it doesn't need. Mine did that for years with the F engine, never had an overheating problem. With the SBC I didn't trust that and installed an aftermarket one.
 
CruisinGA said:
Problem with this is that there is no nipple on the radiator for an overflow tube. Maybe 1/8".

Just took it for another spin and it didn't do it too bad.

Thanks guys, I'll work on getting a good overflow bottle when I get home.


Your nipple may have broken off. Actually, these older F radiators were set up for overflow, they just didn't have a reservoir.

In the picture, you see the nipple below the cap (1 inch long). The cap comes with chain and ring to fit over the nipple, then, you are supposed to put a hose on that goes front-ward and clips down the side (2 clips, you see the top one) and goes to the base of the radiator frame/holder.
DSCN3981 (Small).webp
 
Actually, these older F radiators were set up for overflow, they just didn't have a reservoir.

What do you mean by "older"? Mine is a '73 & my overflow tank is located on the driver fender & he has a '74.

I leave for tellico in 4 hours.

Post up some pics of your truck on Upper or Lower 2. Im super jealous I didn't get my truck done in time. Have a blast!
 
LC_Hamma said:
What do you mean by "older"? Mine is a '73 & my overflow tank is located on the driver fender & he has a '74.

Stock overflow tanks appeared on the scene in FJ40s 1/75 (See SOR for one source). We've been over it enough times on MUD I am convinced of the veracity of that. I forget which month Bailey's truck was built, but anything earlier than 1/75 was retrofit, not OEM, which is fine.
 
I saw in the SOR catalog where the overflow tanks didn't start till 1/75, but this tank mount looks factory on my '73. It has one captured nut welded to the inside of my driver fender & two adjustable uncaptured bolts at the top. I lost the tank - fell out & I ran it over......
 
Last edited:
that is a dead match for the washer res. bracket are you sure some one didn't fab one in?
 
I think I just overfilled the radiator.

It kept pukin a little, but despite running the truck very hard this weekend, it didn't even run warm.

Hamma- Ran 4,5,6,8 yesterday, was with two jeep buddies, one of which is pretty much a newb. Hopefully, when I head back up in two days for GSMTR I will get to run upper 2.

Still managed to lay the 40 on its side on 8.
346434571tIXcri_ph.webp
346434474jEyxDI_ph.webp
 
Last edited:
nicely done bailey, ha ha....


malphrus
 
it's all good, i've seen you make it before



malphrus
 
Back
Top Bottom