Problem while rebuilding rear axle, need advice

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 8, 2004
Threads
45
Messages
1,044
Location
Houston, Texas
During a wrench-a-thon with geoross ande tarbe (fellow mudders and Texas Land Cruiser Club guys) we encountered a problem on the passenger side rear hub spindle. The threads, where the lock nut screws on, in a very small section are fairly mangled. For those that are curious I can't really explain how it happened because the three of us can't figure it out. The problem is the spindle is part of the entire axle assembly. It is not a seperate piece like the front. The three option we came up with are:

1. Find a die with the correct thread pitch and chase it up the threaded spindle to rework the damaged area.

2. Buy a new axle housing.

3. Buy a used axle housing.

Option one is my favorite but i need to find out the thread pitch etc. to locate a correct die. Does anyone have any thoughts or info on what can be done here.

Did I mention my truck is still in Tarbe's garage and that I'm driving his wife's mini van? Please help.

Buck
 
Another option that might help depending on how mangled they are is to sacrifice a nut. I think they are the same pitch as the front hubs are so use one of those.

You take a nut and make a cut across the threads with a hacksaw that goes all the way through the threads. Do that at one of the corners of the nut. If you have a set of precision files you can clean the cut and threads up some and then you that nut to chase the threads. The nut with the cut will act like a die.

The success of this will defend of how bad the threads are but it has worked for me in the past.

Good luck.
 
I have never heard of that before. My FSM is in my truck soo, can someone tell me the size nut I would need? What about a lock nut from the front axle? Can someone confirm for me if they are the same size as the rear?

Thanks Landtank

Buck
 
Try to find a thread file.

I know Snappy and the other truck based sellers carry them but NAPA may have, I don't recall if Sears carries them but it should be enough to clean up the threads so they are useable again.
 
#1 problem is you have Ross helping you :D

I'm sure he told you about his spindle up front when we did his birfs. I worked on that sucker for a bit with a triangle file to fix the threads, then working the nut back and forth until it would thread all the way.
I called Ross yesterday while you guys were messing with it. Hope you got it figured out by now.
 
Buckru said:
I have never heard of that before. My FSM is in my truck soo, can someone tell me the size nut I would need? What about a lock nut from the front axle? Can someone confirm for me if they are the same size as the rear?

Thanks Landtank

Buck


The thread size is not published, I do not know what it is and I do not recall if it is the same as the front. If it is I would go Rick's route for a start. How are the spindles otherwise? If they have wear on the surfaces where the bearings ride perhaps you should consider a housing. You can use either a locker or a non locker housing. If you are not factory locked a locker housing will drop in with no changes. If you are locked all you need to do is cut a notch in the diff mounting surface, using the diff gasket as a template.
 
The "lock nut" idea is a good one, and one that I have employed on other vehicles to "chase" threads that were not too badly damaged.

Unfortunately, the lock nuts on our cruisers are none too wide and you may not be able to repair the area using just one. My suggestion would be to find (2) lock nuts, run them both onto a part of the spindle that is good until they just touch one another (do not jam them), tack weld them across two of the flats (cover the spindle threads). This will yield a "chaser" wide enough to let the trailing nut always have a purchase on several good or repaired threads.

If all else fails:

Year
Part
Model Description Miles Part
Grade Stock# US
Price Dealer Info
1993
Rear Axle
Toyota Land Cruiser CHK RATIO W-ABS 79,036 A 3082 $1250 Airline Used Auto Parts - KOLT USA-TX(Houston) E-mail 1-800-989-0090
1995
Rear Axle
Toyota Land Cruiser 4WD,4X4,12-94,4.5L,A T 021797 $1050 Manuel's Used Auto Parts #2 USA-TX(Houston) E-mail 1-800-778-5071
1995
Rear Axle
Toyota Land Cruiser 2-95, F-AOD,4.5 MFI,CK RATIO,LCKONOT T10811 $1000 Texas Auto Salvage USA-TX(Grand-Prairie) E-mail 1-800-442-6530 / 1-972--263-3306
1997
Rear Axle
Lexus LX450 2-97,4.10 RATIO 61,335 983497 $950 Atlas Foreign Used Auto Parts USA-TX(Pasadena) E-mail 1-800-801-0297
1993
Rear Axle
Toyota Land Cruiser 7-93,W-A.B.S.NOT-533 ,536,SEPARATE 982557 $950 Atlas Foreign Used Auto Parts USA-TX(Pasadena) E-mail 1-800-801-0297
1994
Rear Axle
Toyota Land Cruiser 3-94,4X4,W-ABS,CK 101,226 983490 $950 Atlas Foreign Used Auto Parts USA-TX(Pasadena) E-mail 1-800-801-0297
1997
Rear Axle
Toyota Land Cruiser 4D4R,4.5L,AOD,ASSEMB LY, 982794 $950 Atlas Foreign Used Auto Parts USA-TX(Pasadena) E-mail 1-800-801-0297
 
I appreciate the help. I will pick up a thread file and get after it. If I have to use two locknuts I will but they aren't cheap.

Buck
 
Thread files work well if you take your time and the threads aren't too wasted. IIRC the front and rear threads are the same, Kurt has the front nuts for $3 ea. if you need to make some thread chasers.

About half way down this page;
http://www.cruiseroutfitters.com/lockers.html
 
Hey Guys,
I had a spare front lock nut and gave it a try last night, no love. It was too small. I forgot to mention that I gave that a try.

I really do have faith that the thread on the axle housing can be rescued with some careful filing. But consider Greg, you were coming very close to becoming the new best friend for the parts guy at Meyers Toyota :) .

Ross

PS, a big thanks to Tim and Buck for the moral support on the EGR issues and numerous small things. Both are a credit to the cruiser community. Now if my stupid ECU would get with the program and get back in the swing of things. Evidently 3 restarts is not enough to relearn it idle.
 
Last edited:
I estimate that at it's worst point coming off, we were applying about 300 ft lbs to the lock nut. The grease was burning...we could smell it and see smoke. And we were lucky to get a quarter turn max per re-set.

I won't even begin to describe how it took three guys to get that nut off. I will say it involved Ross holding Buck's foot while Buck was on the floor in the Burt Reynolds pose...:grinpimp: :grinpimp:
 
flintknapper said:
If all else fails:

Year
Part
Model Description Miles Part
Grade Stock# US
Price Dealer Info
1993
Rear Axle
Toyota Land Cruiser CHK RATIO W-ABS 79,036 A 3082 $1250 Airline Used Auto Parts - KOLT USA-TX(Houston) E-mail 1-800-989-0090
1995
Rear Axle
Toyota Land Cruiser 4WD,4X4,12-94,4.5L,A T 021797 $1050 Manuel's Used Auto Parts #2 USA-TX(Houston) E-mail 1-800-778-5071
1995
Rear Axle
Toyota Land Cruiser 2-95, F-AOD,4.5 MFI,CK RATIO,LCKONOT T10811 $1000 Texas Auto Salvage USA-TX(Grand-Prairie) E-mail 1-800-442-6530 / 1-972--263-3306
1997
Rear Axle
Lexus LX450 2-97,4.10 RATIO 61,335 983497 $950 Atlas Foreign Used Auto Parts USA-TX(Pasadena) E-mail 1-800-801-0297
1993
Rear Axle
Toyota Land Cruiser 7-93,W-A.B.S.NOT-533 ,536,SEPARATE 982557 $950 Atlas Foreign Used Auto Parts USA-TX(Pasadena) E-mail 1-800-801-0297
1994
Rear Axle
Toyota Land Cruiser 3-94,4X4,W-ABS,CK 101,226 983490 $950 Atlas Foreign Used Auto Parts USA-TX(Pasadena) E-mail 1-800-801-0297
1997
Rear Axle
Toyota Land Cruiser 4D4R,4.5L,AOD,ASSEMB LY, 982794 $950 Atlas Foreign Used Auto Parts USA-TX(Pasadena) E-mail 1-800-801-0297


Wow! You found that stuff in a hurry!

Hey Buck, you should check to see if any of those have the e-locker...just in case :bounce:
 
tarbe said:
Wow! You found that stuff in a hurry!

Hey Buck, you should check to see if any of those have the e-locker...just in case :bounce:


If all you want is the housing it doesn't really matter. However a spare locked third is always a nice bonus.
 
[
I hope you didn't tell GeoRoss that we don't really have ChupaCabra's here did you?[/QUOTE]

I have seen a couple and even hunted one once but I never got a shot off. Scary critters those Chupa Cabra's.

Buck
 
Buckru said:
[
I hope you didn't tell GeoRoss that we don't really have ChupaCabra's here did you?

I have seen a couple and even hunted one once but I never got a shot off. Scary critters those Chupa Cabra's.

Buck[/QUOTE]


I pulled this .458 bullet out of the last ChupaCabra I shot down near Batesville. Only reason it didn't exit was he weighed 400 lbs and I hit both shoulders.
Expanded 405 Rem.webp
 
flintknapper said:
I hope you didn't tell GeoRoss that we don't really have ChupaCabra's here did you?

TX chupacabras don't scare me flint, if they even exist :D . The ones in AZ are much more scary as they are in such a bad mood due to the heat :D.

Buck,

A set of triangle files, with one on the 1/4" width or a bit smaller would work I think.

Ross
 
I seem to be at a loss for finding a thread file locally in Houston. I have for a triangle file and haven't had much luck with that either. Here is what I have found so far. Any suggestions?

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=93340

http://www.sears.com/sr/javasr/prod...=TOOL&subcat=Files+&+Rasps&BV_UseBVCookie=Yes

http://www.sears.com/sr/javasr/prod...=TOOL&subcat=Files+&+Rasps&BV_UseBVCookie=Yes

From what I have seen a thread file would be the ticket. Again any help in finding one would be appreciated.

Buck
 
Back
Top Bottom