Port matching a 2F?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 18, 2017
Threads
25
Messages
260
Location
Southwest Virginia.
I need to get my intake and exhaust manifolds machined. While they're off, I was wondering if port matching of the intake ports had ever been done?

On an in-line 6, the No. 1 and 6 cylinders are always more lean than the inside four.

I thought perhaps the intake ports could be "matched", in progressively smaller increments from the outside to the middle of the head. Ostensibly increasing airflow volume and velocity a little more evenly amongst the cylinders. Of course, I could be way off base here.

With this in mind, I'm not looking for any huge increases in HP or TQ. I'm aware quite a bit more is necessary for that. What I would be looking for is simply a small increase in efficiency and whatever that translates to. 5 or 10hp increase or whatever. Mostly I suppose this is theoretical anyways. I'm not disappointed in the performance of the 2F

Has anyone done this? Are the coolant passages in the head in the way? Juice not worth the squeeze?
 
Guess which one Is running a port matched 2f.....

98BFAD53-31C9-4171-AF37-6389659914C7.webp
 
In all seriousness- increasing volume may decrease your torque . Matching will help with smoother airflow IF you wanted to install titanium springs and spin your 2F to 8000rpms. (Not recommended). but likely won’t be noticed in the 1000-3000rpm operating range of a 2F.

Popping off the head and milling it for a slight compression bump would make for the most noticeable gains. but even then - not worth the effort unless you need to do some head work.

3fe head and injection is the next step on a 2F for a bump in performance.

10hp is about 10% increase in HP.
10% decrease in vehicle weight would net you the same effective 10hp gains and could likeLy be done for free as well.
 
Last edited:
In all seriousness- increasing volume will decrease your torque . Matching will help with smoother airflow IF you wanted to install titanium springs and spin your 2F to 8000rpms. (Not recommended).

Popping off the head and milling it for a slight compression bump would make for the most noticeable gains. but even then - not worth the effort unless you need to do some head work.

I don't think you understand my question. Or if you even read the entire OP.

I'm happy with the performance of the 2F as is. For a DD, it scoots down the highway at 60mph just fine, and does all I want it to on trails.

What I'm wondering, is if its possible to increase the efficiency of cylinders 1 and 6, by increasing the fuel delivery via a *slight* increase in air velocity and volume to those cylinders. As in 1 and 6 intake ports are opened a little more, 2 and 5 are opened a little less than that, 3 and 4 remain the same.

I dont need more horsepower or torque. What I'm wondering is if fuel delivery can be evened out a little between all the cylinders. A slow motor that runs on all six, is better than a slow motor that runs on all six... but mostly on 2 through 5.
 
With enough time, tools, and money, anything is possible - but unless this goal is just a way to use your time (hobby? retirement?) then it's not going to be worth the time and cost. Is it possible to improve the 2F? Could it have been designed differently? The answer to both these questions is "yes", but in fact it was designed and built that way for specific purposes: to make torque low in the rpm band, to be easily repairable in the field, to be able to run anywhere in the world on any quality/octane of gasoline, and to be affordable. It achieved all those admirably, at the cost of intake and fuel efficiency, among other things.

I suppose you are aware that Offenhauser made an improved intake manifold for the F engines? It didn't revolutionize anything, though I don't know if it had equal-diameter runners or not.
 
I don't think you understand my question. Or if you even read the entire OP.

I'm happy with the performance of the 2F as is. For a DD, it scoots down the highway at 60mph just fine, and does all I want it to on trails.

What I'm wondering, is if its possible to increase the efficiency of cylinders 1 and 6, by increasing the fuel delivery via a *slight* increase in air velocity and volume to those cylinders. As in 1 and 6 intake ports are opened a little more, 2 and 5 are opened a little less than that, 3 and 4 remain the same.

I dont need more horsepower or torque. What I'm wondering is if fuel delivery can be evened out a little between all the cylinders. A slow motor that runs on all six, is better than a slow motor that runs on all six... but mostly on 2 through 5.
I've never heard of anyone doing that but I think it would help. But you would have to pull the head and do the entire tract of 1 and 6. Just opening it up at manifold surface won't do much in my opinion. I would also port n polish all of the exhaust ports and not focus too much on polishing on either the intake or exhaust ports.
 
In subsonic flow you need to constrict the orifice (under same pressure) to increase the flow velocity. But for your concern about leanness in cylinders 1 and 6 you’ll obviously need to increase fuel/air mixture, kind of hard to do in a single carb/manifold system. Here’s how I’m doing it:
1BE7AAC4-9FF9-4CDC-9FC3-8BC4B8160B96.webp


Actually, in reality, I’m using this because it’s what I have, and I’m too stubborn, dumb and cheap to not use it.
 
With enough time, tools, and money, anything is possible - but unless this goal is just a way to use your time (hobby? retirement?) then it's not going to be worth the time and cost. Is it possible to improve the 2F? Could it have been designed differently? The answer to both these questions is "yes", but in fact it was designed and built that way for specific purposes: to make torque low in the rpm band, to be easily repairable in the field, to be able to run anywhere in the world on any quality/octane of gasoline, and to be affordable. It achieved all those admirably, at the cost of intake and fuel efficiency, among other things.

I suppose you are aware that Offenhauser made an improved intake manifold for the F engines? It didn't revolutionize anything, though I don't know if it had equal-diameter runners or not.

Yes, this is all just hobby/retirement stuff haha.

I've looked for offenhauser intakes and can't seem to find any. I'm sure eventually I'll find one. From what I've read and been told, they help, but I've also never hear anyone explain why or show any dyno numbers. In theory they seem effective.

I'm not convinced that Toyota designed the intake and exhaust head ports the way they did "on purpose". More likely, things like unmatched ports arise due to difficulty and cost in manufacturing them. I'm also not convinced that tweaking the head to achieve more near maximum usage of each cylinder would decrease the intended performance.

I've never heard of anyone doing that but I think it would help. But you would have to pull the head and do the entire tract of 1 and 6. Just opening it up at manifold surface won't do much in my opinion. I would also port n polish all of the exhaust ports and not focus too much on polishing on either the intake or exhaust ports.

The thought occured to me when I pulled the manifolds and was looking at it.

I'm sourcing and gathering parts for a 3FE swap and some other stuff in the future. When I pull my 2F, I'm going to rebuild it and will probably fool around with this idea then. Because I like the performance and capabilities of the stock 2F, the rebuild will be done with the intent of fine tuning the stock design. Rather than looking for more horsepower with huge bores, tighter compression and a different cam.
 
Would help what exactly? Hes not looking for performance gains: the objective really isn't defined, so what ''helps" is going to be impossible to measure.

Maybe get a better O2 sensor reading. Oh wait... Maybe an exhaust aroma a little less like an idling Harley? (Actually that's not a bad idea)
 
In subsonic flow you need to constrict the orifice (under same pressure) to increase the flow velocity. But for your concern about leanness in cylinders 1 and 6 you’ll obviously need to increase fuel/air mixture, kind of hard to do in a single carb/manifold system. Here’s how I’m doing it:
View attachment 1850142

Actually, in reality, I’m using this because it’s what I have, and I’m too stubborn, dumb and cheap to not use it.

Where did you get a dual carb manifold
 
the objective really isn't defined...

A precisely tuned "stock" engine.

6 cylinders that suck and burn fuel evenly.

I'm not trying to get gobs more torque or horsepower. I'm looking to refine the designed piece. Knock the rough edges off, so to speak. I'm sure there will be gains made, I just dont expect them to be significant.
 
I'm not trying to get gobs more torque or horsepower. I'm looking to refine the designed piece. Knock the rough edges off, so to speak. I'm sure there will be gains made, I just dont expect them to be significant.

We balance all of our 2Fs and it makes a big difference. They're much smoother and pull really consistently through their entire albeit short RPM range. Not sure if you want to knock that many edges off but it is an option.

I dug around an '87 Offenhauser catalog and found these:
dual intake.webp


Hmmm...a 5588!! Looks slightly different than the pic but the part number matches
5588.webp


It seems Offy only made the dual single for early mills, weird
4bbl intake.webp
 
Last edited:
In the Chevy 250/292... inliners will install lumps in the port to constrict the intake and speed up the velocity and angle at which the flow occurs at the valve. They basically cut out a runner in the head-match ports- and install a lump in both sides of the intake and head. SOme versions bolt in - others get epoxied in. SO if your intent is to speed up #1 and 6 - this would be one way to start to match the outer with inner port speeds. also you can slow down the inner ones by opening up the ports and increasing volume/slowing down 2-5. 250/292 inliner guys are making ALOT more power than a 2F ever will and they have been hopping up those 6’s well before the F engine was even born.

Inliners.org has lots of info.

B06AC4C4-7495-40A1-9E88-16B7CDF39FFD.webp


27D87ACD-E6CC-4244-9926-2B3981A77D91.webp


 
Last edited:
I'm not convinced that Toyota designed the intake and exhaust head ports the way they did "on purpose". More likely, things like unmatched ports arise due to difficulty and cost in manufacturing them.

Exactly. They could not spend a bunch of engineering money and manufacturing costs, if they wanted to price Land Cruisers to sell everywhere including 3rd-world countries like they did.
 
It certainly can't hurt if you're gonna do it yourself - Years ago, when MAF was still in Simi Valley, I had their engine builder build my 2F. I asked him exactly your question and he just shrugged and said it adds a lot of cost to the build for not much return. He said it was much better to spend the money to balance the moving parts and align-bore the block, if necessary. At 2200 rpm, you're prolly not gonna see much difference.

I went with his advise.
 
Years ago, when MAF was still in Simi Valley, I had their engine builder build my 2F.
Who was their engine builder again? The name escapes me. I used to obsess about installing one of their high output 2Fs in my first 40 (10/76, should have never sold it...lol).
 
Last edited:
Turd polishing. haha!

Pretty much, but I really nerd out on this stuff!

The stock 2F is a turd that doesnt stink. I want mine with peanuts though!

In the Chevy 250/292... inliners will install lumps in the port to constrict the intake and speed up the velocity and angle at which the flow occurs at the valve. They basically cut out a runner in the head-match ports- and install a lump in both sides of the intake and head. SOme versions bolt in - others get epoxied in. SO if your intent is to speed up #1 and 6 - this would be one way to start to match the outer with inner port speeds. also you can slow down the inner ones by opening up the ports and increasing volume/slowing down 2-5. 250/292 inliner guys are making ALOT more power than a 2F ever will and they have been hopping up those 6’s well before the F engine was even born.

Inliners.org has lots of info.

View attachment 1850267

View attachment 1850266



These look interesting. I'll have to do some more research here. Thanks!

It certainly can't hurt if you're gonna do it yourself - Years ago, when MAF was still in Simi Valley, I had their engine builder build my 2F. I asked him exactly your question and he just shrugged and said it adds a lot of cost to the build for not much return. He said it was much better to spend the money to balance the moving parts and align-bore the block, if necessary. At 2200 rpm, you're prolly not gonna see much difference.

I went with his advise.

I plan on balancing, aligning-boring etc as well.

Like I said though, I'm not looking for any serious gains...I know what that requires. What I want is the most perfectly balanced, perfectly efficient "stock" motor I can come up with.
 
Last edited:
Back
Top Bottom