Plugging in block heater

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 31, 2015
Threads
45
Messages
197
My battery blanket and block heater are on opposite sides of the engine compartment (as, I'm sure, are yours). Their cords manage to dangle out the front, but that's as far as they go.

How can I plug both in at the same time, to the same extension cord?
Is there a particular type of extension cord that spans the distance between those two plugs fairly well?
 
I'd get a one-to-three and then a 6 foot extension to go over the radiator support. Put it in some split loom and keep dielectric grease on all the connections.

Oh, and pictures of the block heater?
 
I'd get a one-to-three and then a 6 foot extension to go over the radiator support. Put it in some split loom and keep dielectric grease on all the connections.

Oh, and pictures of the block heater?

What would you like to see on the block heater?
 
I've never seen one installed, and am just curious!
 
If together they pull less than a standard 15A circuit you could hardwire them together (using a small waterproof junction box) and have only one plug hanging out the front. If you only use one or the other you could add switches (likely as breakers) to the equation so you could choose either one or run both.

Another (easier) way would be to use a three way connector and build yourself a short extension cord (or buy a short one) to cover the distance.

upload_2016-12-4_17-41-43.webp
 
I would also like the part number for the block heater. Last I checked toyota stopped making them.

I actually bought one new from Toyota last year. I never installed that new one, though, because it turned out the old one still worked and just needed a cord. I'll get the part number for you tomorrow.
 
Last edited:
My block heater is on the DS...same as battery. 1997 LX450. The factory boxed block heater instructions shows this as the proper position (with element coil facing up to 12 o'clock) not sure why a block heater would be on PS of block with insulated 115v lead running around the exhaust manifolds...my previous post is here somewhere regarding this.
 
I've got a 1991 with a 3FE. The block heater lives on the DS, forward of the block coolant drain.

Part:
Engine Heater - Engine Block Type
C0140-00162

I think it cost me less than $20 Canadian.
 
here is a previous post I inputted fwiw.

"the part number was C 0140-00134-S2

the block heater is installed in the core hole plug location as Instructions say:

'L.H.S. 1st from the front. Tie cordset with cable ties to power steering pump hose, and then to front pump bracket. Route cordset to front grill.'

That means in the core plug at the front of the block on the DS. I used a small worn chisel and a 2lb hammer and holding the chisel off centre of the plug (in the depressed area of the plug - not on the edge abutting the block) I gave it a solid wack. The plug spun in the cavity and was easy to pull out with channel lock pliers using a small block of wood on the engine block to lever against.

BTW ... dont worry about the "S2" attached to the part number shown above ... that is the part number that was printed on the box from Toyota that the block heater came in. In the instructions provided it references just C 0140-00134. incidentally this is the same part number shown for the 87-91 Camry 3S-FE; 88-91 Corolla GT-S 4A-GE; and 97 Lexus LX450 1FZ-FE... also various years of Celica that use the 3S-FE and 3S-GE engines

Sorry must edit this to add: the heater coil has to be positioned so that it is directed to "12 o'clock" UP when installed"
 
My battery blanket and block heater are on opposite sides of the engine compartment (as, I'm sure, are yours). Their cords manage to dangle out the front, but that's as far as they go.

How can I plug both in at the same time, to the same extension cord?
Is there a particular type of extension cord that spans the distance between those two plugs fairly well?

Where are you living?
Gas or Diesel?
Zero issues with my gas 1FZ-FE starting at -20°F and it is on single battery.
 
Where are you living?
Gas or Diesel?
Zero issues with my gas 1FZ-FE starting at -20°F and it is on single battery.

I've also had no issues starting mine at -20°F with a old single battery, however I could see the allure of a block heater to speed up the interior warming process.
 
Plus, it's probably not great for an engine to start up that cold. Clearances, oil thickness etc.
 
Yeah, I live in the Northwest Territories with the gas 3FE. Dealing with winter temperatures more in the -30 C/-30 F range.

It's true, though, the truck still starts fine at -20 or even -30 C. It just starts way easier and reduces battery wear, and conceivably engine wear.

It's also psychological. It's nice when the engine doesn't crank low on cold mornings, but just catches without any fuss.
 
That unit sure looks like the one I purchased as OEM! ... Folks are correct to be concerned about oil in the winter. Here are two very well worth while video's to watch from 'ESSO'





watch to the end as there are some surprising/shocking scenes of oil behaviour at very cold temps
 
Back
Top Bottom