PHH - Real time help needed

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 22, 2005
Threads
44
Messages
482
Location
Misery's feed trough
I'm in the middle of doing my PHH and wishing I had my 62 back at the moment. In the process of getting the clamps off the PHH I was a little careless and broke a connector to the left of it. Can someone clue me in on what it is so I can order another one? I looks like it might be an oil pressure sending unit?

The first pic. is pre-break and the second pic shows the connector broken off of it. One other question - can I safely run the vehicle with it like this? I'd like to do my coolant flush this afternoon.

Thanks in advance.

phh1.jpg


phh2.jpg
 
It made me sick to see that!!! I am sorry for what happened. I am not much help, my FSM is at home.

When I was doing mine, I just kept imaging the game "Operation" and tried not to touch anything else. Removing the starter and trans. dipstick tube gave me plenty of room.

I will check the FSM tonight. I am sure you are not the first to break something in that area while changing out the PHH.

Again, sorry that happened. I am sure your heart sunk to your stomach when that occured.

Riley
 
I think that is a knock sensor, and it has happened before, there was even a recent thread about how to "fix" it instead of replacing it. Might try a search on "knock sensor PHH" with in the last few months, or somethin' like that.
 
If I remember correctly from stripping my old block that looks like your rear knock sensor.............remove it and have a look.
 
I think that is knock sensor #2. If you dont knock on your truck you will be ok. Seriously though. I am in the process of putting my top end back together and I can tell you from experience that I think you are in trouble. That thing will be a b**ch to get at. If you are lucky you might be able to get the intake support off, and the fuel filter off to get at it, but even then there may not be enough room. Good luck.
 
I think that is knock sensor #2. If you dont knock on your truck you will be ok. Seriously though. I am in the process of putting my top end back together and I can tell you from experience that I think you are in trouble. That thing will be a b**ch to get at. If you are lucky you might be able to get the intake support off, and the fuel filter off to get at it, but even then there may not be enough room. Good luck.

Kinda confused, he's already got access to it, can't he just put a socket on it and remove it?
 
Thanks for the info. I did a search, it looks like it is the knock sensor and also looks like a bunch of other people have broken theirs also.

I'd like to try the epoxy route before spending the $170 on this part. Does anyone know if there is a way to test it with a mulimeter or something if I glue it? My guess is that it is toasted as it looks like the end of the metal prong on the connector part might have been soldered to something inside the fitting part.

Doing the PHH and having the starter out makes it easy to get at the knock sensor w/ a 27mm socket. I don't think it will be easy to get at with everything back together so I don't want to take a chance on the epoxy fix and then find out it doesn't work.

knock.jpg
 
like to try the epoxy route before spending the $170 on this part.

I would go to an auto wrecker and pull one or two off a wreck, what the heck take a couple of other sensors off while your at it.
 
Yep, you are saving my butt here :beer:

I have the PHH (why isn't it FHH?) in and everything buttoned up now except for the knock sensor.

Thanks again.

The FHH is considered a firewall heater hose (I changed those out when I did my PHH (pesky heater hose).

Riley
 
As I will be doing my PHH soon, would it make sense to unplug or even remove the Knock sensor before wrestling the PHH? I'm not interested in purchasing a $170 sensor either.

Think "Operation"! But really, with the starter and trans. dipstick tube out of the way, there really is enough room to get to it. Use a dremel tool to cut the clamps and a razor knife to cut the hose. Remove the top bolt from the PHH metal tube and reach from under the vehicle with a swivel 12 mm gear drive wrench to just loosen the lower bolt on the pipe. Pull the pipe out of the way, slip the new PHH on the block nipple with the clamps slighty tightened, gently maneuever the pipe back into place (reconnecting the upper bolt and tightening the lower bolt will help to put the pipe back into position). Adjust and tighten the clamps, reinstall the starter and dipstick and you are done. KY or any lubricant of choice is very helpful with the install.

Riley
 
I found that I couldn't put enough leverage on the lower pipe bolt to break it free with a gear wrench. The little 1/4" drive Craftsman wrench and a short socket fit the space and I used a gear wrench as a lever to turn it the first 1/2 turn or so.

The first one I did, the inner clamp was the worst issue. The 2nd one the bolt on the back of the block was. (Two trucks)
 
As I will be doing my PHH soon, would it make sense to unplug or even remove the Knock sensor before wrestling the PHH? I'm not interested in purchasing a $170 sensor either.

If I had to do it again I would probably leave it and just be more careful. I have a half-dozen PHH threads bookmarked that I have studied but none of them talked about the knock sensor. I didn't even see it there with the mess of the other harness/connectors. I would have been much more careful if I had noticed it.

When I did the PHH-knock sensor search there are a bunch of other threads where people broke theirs as well. I'm not sure if that makes me feel better or worse :doh:

I did have a productive day though. Got the PHH done, fuel filter (this was another good job to get done along with the PHH), and flushed all the coolant & refilled w/ red. I'm just hoping my blue silicone PHH doesn't drip now. I wasn't quite sure how much to torque down those clamps that come with the kit. Between the different clamps and softer silicone hose it has a totally different feel than clamping a normal hose.
 
I wasn't quite sure how much to torque down those clamps that come with the kit. Between the different clamps and softer silicone hose it has a totally different feel than clamping a normal hose.

I had the same experience. I just tightened the clamp bolts down until the washers started to squeeze together. I have been checking it every other day since last Saturday and no leaks yet.

Riley
 
Yep, you are saving my butt here :beer:

I have the PHH (why isn't it FHH?) in and everything buttoned up now except for the knock sensor.

Thanks again.

I think your rhetorical question was misunderstood, so I'll weigh in with some levity (knowing your situation turned out to the good! :beer: ).

How about M-effin-HH? MFNHH? MFHH?

Good for you to have done a few of the PM jobs all in one fell swoop.

Hoist yourself a brew or three, and a couple bbq'ed burgers and brats over this holiday weekend!
 
I'm just hoping my blue silicone PHH doesn't drip now. I wasn't quite sure how much to torque down those clamps that come with the kit. Between the different clamps and softer silicone hose it has a totally different feel than clamping a normal hose.

Just keep an eye on the hose itself, and open the radiator cap and peer down into the rad every once in a while. (A normally operating cooling system will use system vacuum as the coolant "shrinks" as it cools to suck from the overflow/reservoir. If you silicone hose is slightly leaky, the vacuum may just suck in air via the PHH.)

Again, good work!
 
Back
Top Bottom