N00b project

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 27, 2002
Threads
8
Messages
51
I've finally made enough progress on this thing to post a few pics. I've been 'wheeling for a long time, but only tried a few minor fab tasks. This time, I wanna do everything myself. I've been going REAL slow and I know I'm gonna make mistakes, but that's how I'm gonna learn.

Mistake #1: I went Ford. =D I know Ford stuff a lot better, so there ya go.
Mistake #2: I ain't so good at welding. I'm getting better, but that out-of-position stuff is pretty dang tough. Rip on me all you want for that; I know it needs improvement.

Plans: Front 60, rear Eaton, coilovers all around. That engine is a 351W stroked to 396 and loaded with Trickflow goodies. Should dyno around 450hp, 500 ft-lbs (flywheel, sea level). It's hooked to a C6 that I just finished rebuilding with TCI guts and an Art Carr full manual off-road valvebody. Atlas II behind that. I know the purists are gonna hate it - I'll make up for it with the next one. hehe.

cruiser02.jpg

cruiser03.jpg
 
Last edited:
usmcruiser said:
To bad you went with Ford, should have been a Chevy. but it looks great.

For the adapters and all, going Chevy definitely would've been easier. I know how to make more power with Ford, though. To each his own.

Do you have any pics of the underside. Does it have a belly or is it gonna be flat?

This is the best I have right now.

http://64.81.100.86/~dtabb/images/Cruiser/2-27-05/Originals/DSC01019.JPG

Like the other link, it's huge. Sorry. I did a lot of cutting and flattening to get the xfer case as high up as possible, but it's still gonna stick down a bit. Shouldn't be too bad, though. I'm using 4-links front and rear, so the link crossmembers will have to hang down a bit anyway. I'm not against cutting up the floorpan to push the drivetrain even higher, but I'm holding off for now. Thoughts?
 
Looks like a lot of people made progress on their projects this weekend. Figured I'd throw out some pics of my own progress.

I wasn't content with the strength of the motor mounts the way i had 'em, so I gussetted them:

mount202.jpg


They're hard to see with the black paint, so here's a pic before the paint:

mount01.jpg


I can't believe how long those took to make. Nuthin but a bandsaw and a 4-1/2" angle grinder to make custom brackets. I figure they took a little over 2 hours per bracket, not including welding and painting. Ouch.

Also got some other goodies this past week:

mount207.jpg


The orbital valve (Danfoss) is from a previous project, but the axle and ram are new. The axle, obviously, is a Rockcrusher diff with Dedenbear inner Cs assembled by Mad 4wd. Looks like they did a great job, but order early - they're sloooooooow. The ram is from Rockstomper. I'm getting tube this week and hopefully will have the heims shortly so I can hang the front axle. More progress pics to come...
 
Looks Like fun, I hope you are not welding around that bomb on the pass side against the wall of the garage. plastic gas cans, propane and thinner is not something to be welding around!!! Be safe and have fun with the project.
 
The gas cans are empty (and have never been used for gas), but you're right about the other stuff. I'll move that. =)
 
congragulations buddy on the ford. i'm running toyota in mine so i can't say which is better but as far as i know ford engines have won more motorsports competitions than chevy. but you know how it goes with die hards, i mean your not going to tell any member of this forum that a j**p is a better vehicle than a toyota, but at least we can all agree on one thing.

and let me highly reccomend that you take off the body, sand blast it and paint it. i never did cause i'm in college and i don't have a garage or the equipment necessary and i thought i should conquer moab before i spent to much money on aesthetics, but i wish i had spent the time and money to restore the body and frame so it will last another 28 years. but when i sand blasted the tub of mine it sucked, very rewarding but it would be way better to do it with the body off. and one more piece of advice from a young guy, i line-x'd my tub and it was worth every dime, it looks great, it's super tough and you can't argue with a no questions asked lifetime warranty.

so good luck to ya and keep up the good work, it's look great.
 
Back
Top Bottom