MPG UPDATE!! Oxygen Sensor question for '91 3FE

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Aggiesdm

***** Regular
Joined
Apr 6, 2013
Threads
81
Messages
1,008
Location
San Antonio, TX
So I just got my first CEL the other day, pulled the code and it is #28, which indicates that #2 Oxygen sensor is not functioning properly. The truck has 276K miles on it and these may be the original sensors, but not sure.

Either way, the truck doesn't seem to be running any different than it has for the last few months...which is not great, but decent. A few months ago, I noticed a slight loss of power and MPG's and I'm wondering if they've been going bad for a while and just threw the code.

Question: How does a truck with a bad O2 sensor normal present itself? What are the symptoms? I'm going to replace them, but I'm hoping that it will do more than clear the CEL and give me a better running truck.
 
Last edited:
OEM sensors are manufacture-discontinued. You will need to find aftermarket replacements. Try for Denso if possible.
 
Yup. 3FE stuff is drying up.
 
OEM sensors are manufacture-discontinued. You will need to find aftermarket replacements. Try for Denso if possible.


Yep, went to my local dealer and he told me ¡NO MAS!

Ended up getting Denso PN#'s 234-4150 and 234-4051!!

I will report my experience.

Derek
 
As long as you do not need an airflow meter, a distributor, an air pump, a radiator or an engine gasket set you are still OK, for the time being.
 
Are they plug and play, or is splicing required?

Says they are exact fit/plug and play. They should arrive tomorrow and ill post my reaction after I get them installed.

$85 delivered for both. Not bad considering OEM were supposed to be $140-180 each.
 
Are they plug and play, or is splicing required?

I received the Denso units in the mail today from Rock Auto. Wow, fast shipping and cheap prices...love it.

Anyway, got the units installed and my CEL was immediately resolved. Cleared the code from the ECU and all is well.

The units were plug-and-play and didn't require ANY alteration to install. The hardest part was getting to the one on the left down tube (aka #1 Oxygen Sensor). It is tucked up between the frame and the heat shield for the catalytic converters. I had to remove the heat shield and the cat protection plate to gain slight access. It was a little slow going, but got it removed and the new one installed. Whole job took about 45 mins.

I drove the truck about 15 miles after I was done and I don't see a huge improvement in performance yet, but hopefully once I fill up with gas and run a tank through it I'll notice a little improvement in MPG's. Not sure if the ECU needs to learn the new sensors or not, but hopefully it does and it will get better over time.
 
I've yet to replace my sensors on my '91, but I am at ~140,000 so I hope to eek a little more time out of the originals. It might help to pull the battery cable or main fuse to reset the ECU, then it should start relearning from the feedback from the new sensors.

Cheers and good to know replacements are still available, even if not OEM.
 
So after a few days, I can report that the cruiser seems to be running better. I drove about 50 miles around town and then filled up to check mpg's. I got right at 10mpg which is about right. I had been getting 8mpg over the last 2 months, so I think the new O2 sensors have helped. I still need to do a valve job and a few other adjustments that may increase the mileage, but at least I'm headed up instead of down.
 
O2 sensors don't fail suddenly, they die a slow and gradual death unless there is physical damage. By the time the 3FE ECU throws a code, they're WELL past due. You can wait for the code to show or you can get better fuel economy and a bit more pep by changing them ASAP.
 
.....You can wait for the code to show or you can get better fuel economy and a bit more pep by changing them ASAP.

Densos ordered, thx Jon (good advice). 142K on the odo, can't hurt, will keep the originals in my growing "original parts" box.
 
O2 sensors don't fail suddenly, they die a slow and gradual death unless there is physical damage. By the time the 3FE ECU throws a code, they're WELL past due. You can wait for the code to show or you can get better fuel economy and a bit more pep by changing them ASAP.

That's good info Jon. I actually thought about asking you this exact question. I have seen a decline for several months, but there was no code. I wondered if they failed suddenly or dwindled over time. Thanks for the info.

Jon, One other question...are the new O2 sensors something that the ECU has to "learn" or are they an instant feedback/response scenario? Seems like it's running better over the last few days, but that could just be wishful thinking? Wondering if the ECU is still learning.
 
Btw, definitely idling smoother and dead-on at 650rpm's! I've been chasing this sporadic idle for a long time and seems that I've finally nailed it.
 
Any time you change anything that has to do with the ECU control system I have found it's a good idea to pull the EFI fuse for a while and let the bits drain back to the bit bucket. I have a habit of doing it after a simple tune up. It certainly doesn't hurt anything and it's always a good idea to clear out any codes that may have registered over time.
Remember, 1986 technology.
 
UPDATE! So my wife's Explorer was in the shop today, so :princess: drove my BMW and I took the TLC to work today. I had to make about a 50mile drive (100mi round trip) and decided to check my highway mileage with the new O2 sensors. I filled up (reg 87 octane unleaded), drove from San Antonio to San Marcos on I-35. All interstate with little traffic, and only light/moderate crosswinds. For 100 miles, I averaged 15.5mpg!!! I couldn't believe it. I've also run through a tank on city-miles and averaged about 9.9mpg. Both of these are a huge improvement over what I was getting before I replaced the O2 sensors. I was averaging about 8mpg city and 10mpg hwy before. Also, the idle has smoothed out considerably and seems to have a little more pep in the motor.

BTW, I had the AC running the whole time and I don't have a working cruise control, so I was really shocked when I saw the milage. I'm sure there are some variables the helped, but it was pretty standard drive for the most part.

If you have original O2 sensors or sensors of unknown age...Change them now! I got the Denso units from Rock Auto for about $85 total/shipped and they've almost payed for themselves in the mileage savings.

Hope this helps you guys and LONG LIVE THE MIGHTY 3FE!!!
 
Last edited:
Back
Top Bottom