Manifold Thermo Sensor Replacement

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 11, 2013
Threads
33
Messages
222
Location
MD
The carb cooling fan's "Manifold Thermo Sensor" (thermistor) for 1977-1992 is $85 (used) at SOR. Has anyone sourced a suitable replacement? As long as it fits the bracket and has a data sheet I can make it work. I don't have wifi for a week and researching is painful on a phone. Thanks.
 
Check w/Georg @ Valley Hybrids(OrangeFJ45)-got one from him some time back
 
you can take the wire and attach it to ground on the fender. only problem is the fan will run every time the key is turned off.
 
I have a few of those available. 818-953-9230. No PMs please.
 
Check w/Georg @ Valley Hybrids(OrangeFJ45)-got one from him some time back
Thanks. I should have explained that mine works fine. After not being able to repair mine, I completed a drop in replacement for the fan controller (relay) itself. It functions like the original but is based on a microprocessor. However, the OEM thermistor has no data sheet so while I can construct a crude temp curve, it's not ideal. I've experimented with using a single-wire temp sensor instead of a thermistor but was curious if someone knew of a modern automotive thermistor with the same diameter and threads.
 
Last edited:
If you made your own controller and your writing your own code, why not write a program to record the curve right from the thermistor as it warms up?
Hmmm, I could. All I really need are the values at 100C (above which the fan switches on) and 85C (when it switches off); I just like data sheets. I could temporarily mount a Dallas temp sensor next to the thermistor and log their values over a few cycles for a good curve.
Another reason I like the forum: there's always something I hadn't thought of or thought through. Thanks.


Sent from my iPhone
 
It would be kinda neat to run the fan output with a PWM so it only makes noise when really hot and slows down and runs for a bit longer than original at a lower speed. Speed proportional to temp through a range...

Arduino, or what?

My idea was always to make it small enough that it could mount right at the fan and sense temp with an IR detector, so the fan would just take a +12v and no other wiring or external controller.
 
Last edited:
It would be kinda neat to run the fan output with a PWM so it only makes noise when really hot and slows down and runs for a bit longer than original at a lower speed. Speed proportional to temp through a range...

It's on my list of wants but I was focused on replicating the OEM controller first.

Arduino, or what?

First design used a PICAXE but after I finished a class on programming a TI ARM processor with C, I went with an ATmega328 (Arduino processor).

My idea was always to make it small enough that it could mount right at the fan and sense temp with an IR detector, so the fan would just take a +12v and no other wiring or external controller.

I designed it to replace the PCB in the fan controller module. I constrained the design to fit in the box and use only the existing 5-wire connector. The only visible difference is that I added an (optional) RGB LED that is red above 100 C, yellow 85-100, and green below 85 C.


I wasn't a EE in college (1984); it's just a hobby.
 
Whew! Way beyond what I could fathom-- I ended up cannibalizing a mechanical cook timer out of a dead toaster oven. Mounted under the dash. Hooked it up to a bilge blower I got out of an old Sea Ray boat. When I shut off the engine, I just click the timer over to 15 mins and let it run-it counts down then shuts off.
It would be kinda nice tho' to have the variable speed and not have to remember to reset the egg timer every time.
 
Whew! Way beyond what I could fathom-- I ended up cannibalizing a mechanical cook timer out of a dead toaster oven. Mounted under the dash. Hooked it up to a bilge blower I got out of an old Sea Ray boat. When I shut off the engine, I just click the timer over to 15 mins and let it run-it counts down then shuts off.
It would be kinda nice tho' to have the variable speed and not have to remember to reset the egg timer every time.
Hey, if it works...
 
I've thought about wanting a replacement to the controller for years. Don't we just need a switch that turns on when sensor registers correct temp, and a timing mechanism to turn it off after 3 minutes? Not sure where the programming comes in?
 
I've thought about wanting a replacement to the controller for years. Don't we just need a switch that turns on when sensor registers correct temp, and a timing mechanism to turn it off after 3 minutes? Not sure where the programming comes in?
Sort of. If you look at the original fan controller, it's an ingenious/complicated design of numerous caps, resistors, and diodes to perform that task. Frankly, I'm not electronically savvy enough to duplicate what Toyota did using only analog components without a lot more study. I'm taking the easy approach and programming a microprocessor to do the "logic." So yes, all you need is a switch and a timer, but the switch can only close immediately after the ignition is switched off and then only if the thermistor returns a voltage value corresponding to a temp greater than 100C. The switch must then stay closed until the temp is below 85C or after 30 minutes, whichever occurs first. It not quite as straightforward as I thought it was going to be.
 
Yes. Back in the shop Monday.
 
I am sure I have several. Leaving for the shop now. Call and leave a message there, and I'll put my hands one them before I call you back.;)
 
Back
Top Bottom