Linkage Dilemma

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Well, its off to the machinist. He does have phenolic but said it is a little more problematic, at least for him. If there is a problem with the aluminum transferring too much heat, I'll go the other route.

Ed
 
Poser said:
Not true bud.....

:D


Well, as I said, Ed, my FJ45 runs fine, as far as I can tell, with an aluminum spacer. I did, by the way, have to get the longer studs, too.
 
IDave said:
:D


Well, as I said, Ed, my FJ45 runs fine, as far as I can tell, with an aluminum spacer. I did, by the way, have to get the longer studs, too.


Why do you have an aluminum spacer? I did a little measuring and think I can increase the thickness enough to solve the clearance problem without running out of threads.

Ed
 
Degnol said:
Well, I see your point, but in theory the carb should not get any hotter than the intake. I'll ask about the phenolic.

Ed
Grade XX Garolite 6"x6"x1" is $17 dollars at McMaster-Carr
 
bsevans said:
Grade XX Garolite 6"x6"x1" is $17 dollars at McMaster-Carr



Thanks for the source. I'm kinda needing to get this thing started and road tested before I depart for the West on the 29th. I'm going to have the aluminum one made and cross my fingers. Is Garolite just a proprietary name for phenolic or does it have better machining properties? My guy has some brand of phenolic/Bakelite, but is more sure of getting the aluminum done in 24 hours.
I cannot believe I've procrastinated this long. :doh:

Ed
 
Degnol said:
Why do you have an aluminum spacer? I did a little measuring and think I can increase the thickness enough to solve the clearance problem without running out of threads.

Ed

My FJ45 came with a WEBER 2 barrel carb, and I wanted a 1 barrel, especially after hearing how well they did. Mark Algazy had one with my name on it in his shop, and waved his magic wand over it, but I needed an insulator, and none were on hand. He had his machinist make some up in aluminum, a little thicker than the stock phenolic.

Yes, you have to get your show on the road (just adding the needed pressure, there, natch! :D)
 
Poser said:
There are two aluminum adapters(read no phenolic spacer) between the aluminum-bodied Weber carb on my, and many other Land Cruisers, some operating with stock exhaust manifolds and others with headers and for some reaons they work just fine......

There are a lot of SBCs running aluminum spacers and adapters between carb and manifold as well.;)

On the 1bbl spacers that I had made, the PCV provision, and it's inherent weakness in the factory design, weighed my decision away from the phenalic.
The two-barrel PCV tube is also the weak link in the spacer, but not nearly as bad as in the 1bbl. Still, if I ever had to go down that road, I would opt for the aluminum over the phenalic for longest-term durability.

Ed, did you consider the 73 transition year bellcrank. It still works on the cable, but it is mounted horizontally. That is what I have used in the past with the 2F intake.;)

Best

Mark A.

P.S. Got your check.:cool:
 
Degnol said:
Thanks for the source. Is Garolite just a proprietary name for phenolic or does it have better machining properties?
Ed
Garolite is a brand of phenolic that is fabricated in a number of variations to get different properties. The phenolic that a machinist needs to be cautious of is G10/G11. Those two versions need to be machined in a liquid bath to avoid any dust. The other brands of garolite are free machining and can be worked just like aluminum on a mill or lathe. We used Garolite extensively to make fixtures to mount missile components and subject them to severe vibration under thermal cycling from <-40C to >+100C.
 
Back
Top Bottom