Interior cage ideas

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 1, 2004
Threads
245
Messages
3,540
Location
Staunton, VA
This is what I'm working with. No headliner or interior other than the dash. It's been rolled and pushed back straight. I'm not making a race truck out of this thing - more a cruiser arounder with occasional light-mild wheeling trips ( I live in VA after all). If my wheeling gets more frequent or aggressive I will reevaluate the cage.

J front springs and stock rear springs with 315s (for perspetive)
IMG_0502.webp


I would REALLY like a cage to stay all interior, but I have a couple questions.

- I'm 6' 3". Has anyone out there of similar height run the A pillar support inside the cab? Is it miserable? Is it unsafe?

- I'd prefer to weld the cage to a plate and bolt to the body overtop the body mounts. Seems like that would be at least as safe as the OEM body. Or maybe I am completely off base.

- I'm really only interested in protecting the front two seats and triangulating to the rear. From what I've seen of wrecked 80s it's 90% of the time when the A pilar/front cab gets smashed. I don't think I've ever seen an 80 land on the rear roof. And with all the weight I removed along with the bob I think that would be even more unlikely.

Let me hear the ideas from guys that have run a cage. What did you like? what did you not like?
My old 40's cage was made from welded together poop-pipe (PO's work) with no bends and it went through 2 pretty significant rolls without issue... I would like my 80 to be as safe as a 1st gen 4runner or a stock fj40...
 
Yeah, that thing is sick I've seen that picture about a million times but can't ever seem to find more info. The picture doesn't really answer my question, though. Do you know what it's called? As in something I can google to find more pictures or a build? I'd like to see the inside of the cab.



Maybe the A-pillar support on the outside to keep from cracking my skull in an on-road frontal impact.
 
I've also seen some random pics of Landcruiserphils interior cage. Haven't seen anything he's written about whether it's comfortable or not and I can't seem to find the pictures on Slees website.
 
I have pondered similar scenarios and if you want to keep it right and inside and the interior is stripped, I would work it directly into the body. Trim spars and interior bracing, insert/recess tubes into the spaces and stitch the body directly to the cage and essentially make the cage integral to the body. Put floor plates in and sandwich with bolts to plates underneath, the tie into the frame with poly bushings to help prevent metal fatigue and cracking due to rigid mounting.

This is what I'm thinking of doing when the time comes. Never seen it done quite that way, but should give the most interior space and protection in one lick. Worst thing about it is it will be very time consuming to build if you do it right.
 
I have pondered similar scenarios and if you want to keep it right and inside and the interior is stripped, I would work it directly into the body. Trim spars and interior bracing, insert/recess tubes into the spaces and stitch the body directly to the cage and essentially make the cage integral to the body. Put floor plates in and sandwich with bolts to plates underneath, the tie into the frame with poly bushings to help prevent metal fatigue and cracking due to rigid mounting.

This is what I'm thinking of doing when the time comes. Never seen it done quite that way, but should give the most interior space and protection in one lick. Worst thing about it is it will be very time consuming to build if you do it right.


That's a great idea. @2fpower did something similar but I'm not sure if he tied it down to the frame. He slid some tube, starting at the B or C pillar, inside the edge of the roof down to the windshield frame. Awesome idea, but I dunno if I trust my crumpled windshield frame enough. I think I would need to go on down the frame or body mount.
 
I've also seen some random pics of Landcruiserphils interior cage. Haven't seen anything he's written about whether it's comfortable or not and I can't seem to find the pictures on Slees website.

My cage was very comfortable, very tight, and not in my way at 6'1". With that said it was built to AID in supporting the Land Cruisers body and keep mainly the A pilier (main weak point) from totally collapsing. It did not have the much needed cross bracing the poster will require with most of the roof cut away. Also was not tied to the frame. If one feels the need to tied the cage to the frame to get the required protection for their needs then the seats and belts must also be tied to the frame to be correct.
 
Is the windshield installed? If not then check out this site More Cayman photos… – Cage This

You can reinforce the A-pillar similar to the second pic on that page. Of course, when you get into this kind of cage build, we may be crossing the line on what you are looking at doing with the rig.

Also, the plate by the dash seems viable, I have seen several Heep kits and a Samurai kit made with dash plates instead of full down bars. The generally are tied to the door jamb to help increase strength.

And as far as reinforcing the A-pillar, the above would technique would help with that as well.
 
From what I've seen of wrecked 80s it's 90% of the time when the A pilar/front cab gets smashed. I don't think I've ever seen an 80 land on the rear roof.

I have and the body shell absorbed the majority of a direct roll from tire to roof, flawlessly.

I wouldn't doubt that a high percentage of those with A pillar deformity post roll, don't have aftermarket or improperly installed windshields, since integral to the integrity of the cab.

I would like my 80 to be as safe as a stock fj40...

If the bar is set that low, why bother with a cage?
 
My cage was very comfortable, very tight, and not in my way at 6'1". With that said it was built to AID in supporting the Land Cruisers body and keep mainly the A pilier (main weak point) from totally collapsing. It did not have the much needed cross bracing the poster will require with most of the roof cut away. Also was not tied to the frame. If one feels the need to tied the cage to the frame to get the required protection for their needs then the seats and belts must also be tied to the frame to be correct.

I actually do not want the frame tied to the cage. I think I am probably going to run large plates overtop of the body mounts and weld the cage to the plates. I'd prefer to run my factory seats and factory seatbelt setups.

Is the windshield installed? If not then check out this site More Cayman photos… – Cage This

You can reinforce the A-pillar similar to the second pic on that page. Of course, when you get into this kind of cage build, we may be crossing the line on what you are looking at doing with the rig.

Also, the plate by the dash seems viable, I have seen several Heep kits and a Samurai kit made with dash plates instead of full down bars. The generally are tied to the door jamb to help increase strength.

And as far as reinforcing the A-pillar, the above would technique would help with that as well.

That cayman cage is slick. I'm guessing that guy has a little bigger budget than I have. I really like how it's tied to the A-pillar and down beside the dash. It gets it out away from your knee which I think will be an issue for me with a traditional cage setup.

I have and the body shell absorbed the majority of a direct roll from tire to roof, flawlessly.

I wouldn't doubt that a high percentage of those with A pillar deformity post roll, don't have aftermarket or improperly installed windshields, since integral to the integrity of the cab.



If the bar is set that low, why bother with a cage?

The cage is mostly to appease the internet doomsdayers. I'm not wise enough to consider things like dying when I'm on the way to the grocery store :rolleyes:. In all seriousness, though, I would like to not be crushed if the thing ended up on it's lid, but like I said before, it's not a race truck and I'm not a hardcore wheeler.

I think roll cage may be a misnomer. I just want a "Cage That Gives the Bent Areas of my Cab Some Extra Support in the Event of an Accident and Won't Turn Me Into a Vegetable In a Headon Collision". Roll cage seems easier to say though.
 
That's a great idea. @2fpower did something similar but I'm not sure if he tied it down to the frame. He slid some tube, starting at the B or C pillar, inside the edge of the roof down to the windshield frame. Awesome idea, but I dunno if I trust my crumpled windshield frame enough. I think I would need to go on down the frame or body mount.

I tied to frame behind passenger seats with the X bracing. Plates by rear tailgate. Otherwise tied to the stock A and B pillars. I was going to drop a tube at the B pillar; however when cutting it discovered how many layers of reinforcing steel there, so decided to stay stock.
 
I tied to frame behind passenger seats with the X bracing. Plates by rear tailgate. Otherwise tied to the stock A and B pillars. I was going to drop a tube at the B pillar; however when cutting it discovered how many layers of reinforcing steel there, so decided to stay stock.

I think for your purposes your cage will work fine. I don't know if my A-pillars, having been crushed and straightened, are as strong as yours. Although, the 4 ton portapower was about maxed out trying to straighten those suckers...
 
I am excited to see what you come up with, as I agree it is my weak point of the cage.
 
Back
Top Bottom