Help.. Some questions....

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 4, 2005
Threads
4
Messages
61
Location
Baton Rouge, LA
Today i got the urge to replace the fluids in the trans (3 speed) and tranfer case (had the cruiser 2 month now). Every thing went fine with the transmission change and it shifts better now! But when i went to drain the Transfer it had hardly any oil at all. So i marked up as the PO fault and filled it up. But it leaks out of the rear seal (by the parking brake) a drop every few mins. So now i know why it was low. Obviously i need a new seal.

But my question is will my transfer be ok if it is low as long as i dont go 4wd?

I planning to get another 3spd and xfer to rebuild and swap in the near future. I have a 3spd lined up but need a 3 spd transfer. I have a 4 spd transmission anyone want to trade 4spd trans for 3 spd transfer?

Next question: I went ro grease up my birfields and removed the greas plug near the brakes. How much grease do i put in there?

Thanks in advance. Sorry I am not up to par with my 4wd stuff. Before i had this i was into Hi-performance mustangs so i know more about that. :)
 
Changing the rear seal is no big deal. Yes, you must keep it filled with lube regardless of 2WD or 4WD. There's a lot in there in motion even when in 2WD.

Also, a common seal problem is the one between the TC and the tranny. Was the tranny overfull when you pulled the plug? If so you have lube being pumped from the TC up to the tranny.
 
Rice said:
Changing the rear seal is no big deal. Yes, you must keep it filled with lube regardless of 2WD or 4WD. There's a lot in there in motion even when in 2WD.

Also, a common seal problem is the one between the TC and the tranny. Was the tranny overfull when you pulled the plug? If so you have lube being pumped from the TC up to the tranny.


Thanks. I need to check into getting another seal. The transmission did not seem overfilled.

I did put it into 4wd after filling and it shifted into 4wd fine but it did not want to shift back into 2wd.

Is it hard to rebuild the transfer. I have seen the kits. If i got it out anyway should i rebuild it?
 
LNDCRZR said:
Thanks. I need to check into getting another seal. The transmission did not seem overfilled.

I did put it into 4wd after filling and it shifted into 4wd fine but it did not want to shift back into 2wd.

Is it hard to rebuild the transfer. I have seen the kits. If i got it out anyway should i rebuild it?


Most folks (including me) would argue that there are enough spare TC's out there (for cheap) that rebuilding just isn't worth it (trannies too).

When mine eventually croaks I already have the other that's going in its place.

If you want something to do on a Saturday perhaps you can rebuild the one that comes out and keep it as a spare.

Rice
 
you said that you had trouble shifting back into 2wd from 4wd, try backing up a bit first. when 4wd is engaged it kinda bind's the gears together or puts pressure on them and backing will release that and make it alot easier to go back into 2wd.

also as far as grease in the knuckles i have heard that keeping them about 1/2 full to 3/4 full is best, how to tell i really dont know, i just kept pumping the grease gun till i thought it was enough, i figured some is better then none.

good luck!
 
my question, why do you want to keep it a 3spd, if:
1. you have a 4spd on the ground
2. you plan to pull the 3 that's in it now
3. you want to rebuild a tranny

of course the'res nothing wrong with the 3spd, just given the choice I would take a 4 over a 3 any day.
the slick setup is a 4spd tranny in front of a 3spd transfer case.
 
PabloCruise said:
I second!

You'll get a lower first. Mating the 3 spd t-case to the 4 spd is supposed to be fairly easy

Easy yes. Cheap not, Nice yes it is, that is what I have in my 69 fj40 and am thinking of doing the same in the 45 after coming into some problems with my pto setup. Advanced adapters has everything you need for the swap and it gives you 10 lower in low range.

Greasing the Birfs from the plug will not really do the job of getting to the balls in the birfs, The only way to do it right is tear them down.
 
brian said:
my question, why do you want to keep it a 3spd, if:
1. you have a 4spd on the ground
2. you plan to pull the 3 that's in it now
3. you want to rebuild a tranny

of course the'res nothing wrong with the 3spd, just given the choice I would take a 4 over a 3 any day.
the slick setup is a 4spd tranny in front of a 3spd transfer case.

I was going to stick with thte 3spd for $$$ reasons. But If that is a good setup then i will try to go with that and get the parts one by one. I still need a lot of parts to swap i think. All I have is the 4 spd trans (excellent shape). Still researching what all i need to finish this conversion. I am new to cruisers......
 
Greasing the Birfs from the plug will not really do the job of getting to the balls in the birfs, The only way to do it right is tear them down.[/QUOTE]

That statement pretty much nailed it! I've never pulled that plug to grease the knuckles, always tore it down.

the slick setup is a 4spd tranny in front of a 3spd transfer case.

This will be ok for a resto or DD, any offroading I wouldn't bother - think SM___.
 
Rice said:
Changing the rear seal is no big deal.


I am just trying to see if i understand the step to do this:

1. drain transfer oil
2. remove rear drive shaft.
3. remove emergency brake
4. pop old seal out and replace
5. put everything back on and fill with oil

Is this right. Any tips to make this easier?
 
I just did this, looked like the PO had done it before me a long time ago. It looked like he put the ebrake back on dry and rolled the lip of the seal inward. I put a thin film of grease on the brake backing and it went on no problem. Otherwise just as you describe, no problem took about 20 min.

Les
 
LNDCRZR said:
I am just trying to see if i understand the step to do this:

1. drain transfer oil
2. remove rear drive shaft.
3. remove emergency brake
4. pop old seal out and replace
5. put everything back on and fill with oil

Is this right. Any tips to make this easier?

Umm, not quite. There's the flange that connects the driveline to consider - it's actually what the seal is supposed to seal. The nut that holds that flange can be pretty tight and if there are any grooves cut around the flange where the seal lip rides a new seal may not help much. That groove has to be dealt with. A new flange is a good way, and a speedi-sleeve that installs onto the flange to give a new ungrooved sealing surface to the new seal is also good.
 
honk said:
Umm, not quite. There's the flange that connects the driveline to consider - it's actually what the seal is supposed to seal. The nut that holds that flange can be pretty tight and if there are any grooves cut around the flange where the seal lip rides a new seal may not help much. That groove has to be dealt with. A new flange is a good way, and a speedi-sleeve that installs onto the flange to give a new ungrooved sealing surface to the new seal is also good.

Ok. I am trying to picture this flange. Can you help me identify it? Is it 36104 in the link below?

Parts

If i get a new flange do i need the speedi sleeve? Thanks.
 
Last edited:
36104. Yup. I put mine on the lathe and skimmed it down just enough to give the seal a new surface to ride on.

Works so far but will probably come back to haunt me, just like every other #$@@#%%^#ng mod I do. Why in hell can't I make a clean deal of any @#%%#ng project I start and . . . Oh, sorry. Uh, yeah, that's the part all right. Well, uh, see ya. :o
 
honk said:
Umm, not quite. There's the flange that connects the driveline to consider - it's actually what the seal is supposed to seal. The nut that holds that flange can be pretty tight and if there are any grooves cut around the flange where the seal lip rides a new seal may not help much. That groove has to be dealt with. A new flange is a good way, and a speedi-sleeve that installs onto the flange to give a new ungrooved sealing surface to the new seal is also good.

Honk, you are talking about the front output seal. The conversation started around the rear output seal at the e-brake...

The surface attached to the e-brake is what seals in the rear. If there is a groove large enough to catch your finger nail on, your seal will not hold up. The you go for the speedi-sleeve.

And there is a stake nut holding the e-brake drum on. Order a new one and replace when you do the seal...
 
Back
Top Bottom