Fzj80 getting hot.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Not sure about the Aussie 94's but the US spec 94 has a good black hub fan clutch. Recently I replaced my 93 black hub clutch (same as 94) with 10kcst Lucas silicone oil and it made a big difference. Member @Tools R Us has great info on this matter.
After completely draining my clutch I added about 45ml of the 10k oil. I also set the internal opening temp to approximately 100F. I didn't experience over heating before but the fan pulls a considerable amount more air and does so sooner.
 
Not sure about the Aussie 94's but the US spec 94 has a good black hub fan clutch. Recently I replaced my 93 black hub clutch (same as 94) with 10kcst Lucas silicone oil and it made a big difference. Member @Tools R Us has great info on this matter.
After completely draining my clutch I added about 45ml of the 10k oil. I also set the internal opening temp to approximately 100F. I didn't experience over heating before but the fan pulls a considerable amount more air and does so sooner.
Thanks for the reply.... by black hub im guessing your refering to the painted area behind the fan.
Ive seen blue mentioned but until i get to it i have no idea
Ive ordered 2 doses of ome oil for the fan clutch.
Ill replace it if i have to but it will need to be from the states.
As i said its a daily driver that im to paranoid to drive.
Lost a 900 dollar job today through yncertainty.
I want to do the job properly but i want to do it right instages without remedial or reptitive repairs.
Ill loose my rag if it comes to that point
 
Was also looking for the fan clutch oil thread but ive only found page after page of reference to it.
Could someone please post the link...chèers dale
I have heard of silicone fill it to the brim.an seal it down tight
 
Slipping belts could definitely cause your problems as the belts drive the fan. If they were slipping the fan was not spinning at the right speed.

Also be careful with your coolant, if it's red replace with red if it is green replace with green do not mix.
 
Thanks for the reply.... by black hub im guessing your refering to the painted area behind the fan.
Ive seen blue mentioned but until i get to it i have no idea
Ive ordered 2 doses of ome oil for the fan clutch.
Ill replace it if i have to but it will need to be from the states.
As i said its a daily driver that im to paranoid to drive.
Lost a 900 dollar job today through yncertainty.
I want to do the job properly but i want to do it right instages without remedial or reptitive repairs.
Ill loose my rag if it comes to that point
Yes, the hub is connected directly to the pulley. If yours is black put 10k and no more than 12k oil in it. I hink you meant that you bought OEM oil. The OEM oil is light and won't render much change unless your clutch now in an under services condition. Always use OEM belts. Check Amazon for an Aisin water pump.
 
Yes i got genuine belts,learnt that the hard way.
The belts currently on the truck cost me as much as genuine and have squeeled and slipped for 12 months or so.
 
Im considering doing all my hoses while doing the radiator, anyone used silicone hoses as replacements or see any benifit in it?
Can get a complete set on US ebay including the full set of heater hoses for around 180 us... postage and wxchange rates suck a bit though
 
Ok so tomorrow it all begins.
Ive been using the wifes car this week while i get parts together.
Tomorrow and sunday im fitting...
New 3 core radiator
Reoiling / resetting fan clutch.
Fitting new radiator hoses.
Fitting 80 specific twin gauge a pillar pod
Fitting japanese stepper temp gauge with warning light and alarm.
Fitting new belts.
New coolant.
Oil and filter.

One question is this temp gauge is able to be set so the warning light and alarm come on at a pre determined temp.
What temp would you recomend i set it at and what is the optimal operating temp of the 1fz fe?

Ill post some pics of my progress and the end result when i get there
I also got some leather bucket seats out of an Australian built xr8 falcon today witch aparantly are a very easy bolt in
 
some 80 owners claim to see 220 regularly. I feel that this is too hot, I saw between 185 F (85 C) to 195 F (90 C) all the time. I only got to the higher end when climbing 10,000' passes fully loaded.

The other thing to consider is that when my HG blew the temp went from normal to WAY HOT in about 10 seconds. I litterally was watching my digital gauge when it happened. The temp raised about as fast as you can read this 87, 88, 89, 90, 92, 95, 98, 102, 104 shut down (My gauge is in Celcius)
 
Thankyou kind sir!
So maybe 90ish would be a good place to set it.
Im realy hoping i dont get to see where my HG blows as i realy cant aford that drama right now...ive easily just spent a grand.
If you dont mind i may need some pointers through the process.
The fan clutch is probably the thing im dreading the most however i did buy a IR thermometer witch will aid with setting it
 
What is this Japanese stepper temp gauge with warning light that you speak of?
 
Its a 52mm or 2 inch gauge thats made in japan.
Aparantly stepper motor gauges are the most acurate due to the design.
These gauges are race spec and i got it from a local 4x4 company.
Audable alarm and warning lights adjustable but i only got it yesterday so i havnt played around with it yet but it looks pretty well made and came with sender ect... $100 australian.

Water Temp Gauge 52mm Audible Alarm for Toyota LandCruiser Prado - BLUE BACKLIT
 
Well its 4pm and the trucks in 100 pieces.

Just doing the spark plugs while the radiators out and i can stand in the engine bay.
Ive had some denso iridium plugs for 6 months or so so its about time they went in.
Ive oiled the fan will test where it opens tonight or tomorrow.
Thermostats done and old hoses and belts are off ready for the new ones.
I forgot what a mongeral these things were to remove radiators on...especialy with duel batteries
 
Well its all done and the new gauge isnt installed properly but ive got it working cable tied to the passengers grab handle.
My stock age is still going all the way up to just under red so i guess its toast.
The hottest ive seen on the new gauge after a quick drive is about 82.
Massive improvement in smothness and response with the new plugs.
I topped up the fan oil and adjusted it to open at 45c or as best as i could.

Hopefuly im sorted.
 
Well today i drove it to work for the first time witch is about a 25 minute drive in stop start traffic with some free flowing areas.
I also had to drop the boss's wife home this afternoon witch ment i was driving another 35 or so mu utes home and the highest temperature i reached was 87c.
The stock gauge was sitting just under red so mostly it was a gauge issue from the outset but if it cotinues to sit around these temps ill at least have peace of mind everythings renewed. The heater works awsumly now witch it didnt before so im guessing the thermostat was definatly an issue anyway.
 
Back
Top Bottom