Front Axle service

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I was never able to find any brass tools,drifts, rod or anything around Philly. I ended up getting a brass pipe plug from lowes and holding it with a vice grip and beating the crap out of it to get the cone washers out. It worked. I first tried using a regular hammer and leaving the nuts on the studs and immediately bent the heck out of the stud. Dont try that.

I think amazon sells both the 54mm socket and the brass tools, but I needed them quicker.

Ben
 
Last edited:
I never used a punch for the cone washers. I had the nuts flush with the bolt and used te drift against that and also tapped next to the bolt. quick and easy.

Maybe a friend has one you can borrow. I would go ahead and order one online so you will have it next time.
 
No, actually I find that a big brass hammer is the best for that. I hit it softly and square to the studs with the nuts still on and flush at the extreme end of the stud. It takes surprisingly little force for whatever reason. :cheers:

Oh yeah! I like brass hammmer too. I just wanted to make sure that moab_b2 understood that when you said skip the drift thing all together. :cheers:
 
Well I have had absolutly no luck locally. Amazon will deliver the socket and drift next week. I hope to have all of the teardown and clean up done by the time it arrives for install. I still am going to to to our local metal supply to see if they have any brass, but their online site didnt give me much hope. Thanks guys for the help, and for those who found brass drifts locally, consider yourself lucky.
 
Last edited:
I have finished the teardown of the drivers side (not the problem side) and found that the trunion and wheel bearings look new. The wheel bearings are Timkin and the trunion are are Koyo. They seem to be original, but that seems really wierd as the LC has 252K miles on it. Is this normal to have next to no wear?

I am not new to bearing repacking/replacing. I have been servicing my ford trucks for a while and was happy to get 60k out of bearins. 250k seems insane. Is this normal?

Also I have read about the pipem method to remove the shaft from the star knuckle thingy lol. Does anyone have a picture or video of the process. Also if you use a pipe wouldnt it destroy thesnapring down in there? Where do you get anther one? Are they common enough to get at any autoparts store?
 
Last edited:
I have finished the teardown of the drivers side (not the problem side) and found that the trunion and wheel bearings look new. The wheel bearings are Timkin and the trunion are are Koyo. They seem to be original, but that seems really wierd as the LC has 252K miles on it. Is this normal to have next to no wear?

I am not new to bearing repacking/replacing. I have been servicing my ford trucks for a while and was happy to get 60k out of bearins. 250k seems insane. Is this normal?

Yes. But OEM should be Koyo all around, IIRC. If you have Timkens, I'd wager they've been replaced.
I pulled mine @ 230k miles and aside from some slight discoloration, they were fine.

moab_b2 said:
Also I have read about the pipem method to remove the shaft from the star knuckle thingy lol. Does anyone have a picture or video of the process. Also if you use a pipe wouldnt it destroy thesnapring down in there? Where do you get anther one? Are they common enough to get at any autoparts store?

There is a DVD. search "birfield DVD" and I'm sure it'll show up.
I get the snaprings from CarQuest. Didn't write down the part#, but they should be able to match it based on measurements. And I'm sure Cruiserdan has em, too.
 
I have that dvd and it doesnt cover tear down of the birf.It goes over the service and replacement of bearings and seals.
 
I used to be pro-brass hammer, but I'm now a convert to the "tiny screwdriver" method... try it once... with practice you can get all 6 cone washers off in under a minute and not even wake the baby. Just tap a tiny screwdriver into the slot of the cone washer with a normal sized hammer (NSFH)- it will expand, then you use the screwdriver as a handle to gently remove it. You don't even need to come at it from the side, parallel to the stud is fine just hit that little slot head on with the little screwdriver and it will slip right off..

you still need to tap the drive flange with the brass hammer to break it free though. hth...
 
My cone washers all but popped off when I got the nuts off. 1 had to be tapped lightly on the side with a hammer before it came off as well.

Question though. What is the part # for the replacement snapring for the inside of the birf? I keep hearing that these come with the kit that CruiserDan sends out. I have 2 different sets of snaprings and have no idea what they go to. Since I have had sme clicking, I was going to swap birfs after tearing them down, but I want to make sure I have the right snapring before doing so. Anyone know exactly so I can match the part# with what I have. THanks
 
Back
Top Bottom