Freaking Muffler Shops!!!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 5, 2003
Threads
149
Messages
1,144
Location
Golden, CO
All I want is sliders! To do that I have to get rid of the dual exhaust that is in the way. So I m aware of what needs to be done.

Swapping the block huggers for some center dump rams horns (got em all ready)
Will do Woodys y-pipe mod, keep the exhaust inside and above the frame and dump it out behind the DS rear wheel.

So I have the rams horns and Borla muffler (ebay luck out). and all I need is some pipe bent up.

Local guy wants $495 to do the work !!! WTF! I hate california, everything is more $$

So the quest continues. Is this something I could do myself? Anyone have a lead to get the y-pipe woody talks about? Its like $40 and a few pieces of bent tubing can't be that expensive!

Tried to find the old threads with the exhaust pictures but to no avail. Anyone know a good (and cheap) exhaust shop in nortthern CA?

I am going to run over budget on this one and the sliders will have to wait....again. :mad:

Just venting a bit. Dan
 
Go to a smallish town and find a good ole boy muffler shop. That is if there are any good ole boys left in Cali. My custom shop here in beautiful Amarillo, Texas would charge about 250, work done that day, to my specs.
Best wishes, DocB.
 
Thanks mike. I think I'll run down to napa and order the pipe then see what they want to charge me for the rest. Thanks

Dan
 
I agree about finding a local place in a smaller town. I asked around some hotrod shows about exhaust when I needed to get mine done on the FJ45, and found a great place 45mins away, but worth every red cent california made on the gas tax to get there. they did a perfect job, flanged in three places, dynomax muffler, routed around PTO shaft, etc, all for $310 taxed. Alot of places these days dont like actually bending pipe anymore, they just want the bolt in systems and simple s*** like mufflers only and tips. less work...
 
i paid the "local" shop 300ish to replace a rusted custom system. all they had to do was copy what was there, WORD FOR WORD.

about a week 1&half later i figured out they replaced my 2 1/2" stuff, with 2" crap. about the same time a baffle in the muffler poped a spot weld, and now has a VERY tinnie rattle at idle and under lite loads.

guess i should have made it out of SS like i was planning on doing, will now though.......
 
DocB said:
Go to a smallish town and find a good ole boy muffler shop. That is if there are any good ole boys left in Cali. .

Actually because of labor laws and workman's compensation laws, the trend in California is to single person, owner-operator shops and independent contractors. They are generall "good ole boys" and they are cheaper.

The laws makes it too expensive to hire employees. It is cheaper to just adopt them instead.
 
Yep did a cj5 yesterday.2 1/4"y pipe in to a 3' single,new studs and hangers,his muffler for $350.cnd.Sounds like i need a franchise in cali. cause thats a nice profit.I 2nd the look for the billy bob's muffler and bait and hot rod welding shop.
 
You could try doing it yourself. Just need a sawzall and a welder.
You can buy mandrel bends
These guys are the cheapest I foundhttp://www.globaltecheng.com/elbows.htm?OVRAW=mandrel%20bends&OVKEY=mandrel%20bends&OVMTC=standard

Walker sells them too. You can get bend part #'s from their website and order them from Jegs or Summit.

Flowmaster makes assorted two into one Y pipes.
You can buy one coupler at the auto parts store, saw the expanded parts off in 2" wide pieces to use as couplers, so you don't have to go to a shop to get the ends expanded and enlarged..

Flowmaster makes universal tailpipe kits . They come with bends and pipe. Also can be ordered from Jegs or Summit.

I had never done exh work before, did it in less than a day. Easier than I thought.


Mine with Global tech mandrel bends, flowmaster Y piece, and Flowmaster 3" universal tailpipe kit.
lc57.jpg

lc58a.jpg
 
I really lucked out on mine. Went to the local Cole's Muffler show (a NE franchise I think). I got quoted $150 for mine and BS with the guy.. who was the manager of the shop.. and at the end, he charged me $125 for it. Try different shops, even if they have the same name, to see if they will charge different prices.
 
Dan,

Try Dave's Muffler Shop in Sonoma. (707) 939-8024. I had mine done over there, 350SBC, custom Y collector, single aluminized 2.5" pipe, flowmaster, exit behind passenger's rear tire for $200 about two years ago. He does a lot of cruisers.

Dave
(no, not my muffler shop :) )
 
Dan , yup , it is expensive but that price is high , I had mine done at Jonny Franklin , Santa Rosa Ave , and they installed horns , flowmaster Y , all tubing and hangers , crossover , muffler , exiting just like you want and they bent it around my aux. tank ,, $ 355.00 out the door.
 
add , they are cool about letting you stand there and watch and be able to have it your way and account for clearances and heat and routing that you want not the muffler tard , get ahold of the skinny guy , I think Craig.
 
Yep, I have had a couple of my mufflers done at Johny Franklin's over the years, good work @ reasonable price.


drohweder said:
WTF! I hate california, everything is more $$

Yep, but even the shop flunky has to pay $1200/month for his 1br apartment rent, and the bosses 3 BR 1200sq ft house on a 30 x50 lot is going for $400K.
Ya'll just get ready for the flood of Kalifornians as they retire.
 
Where you at in CA?? In know a great guy in San Jose area, let me know if its close.
 
I used to have good experiences and beautiful work done at Babe's Muffler on Camden right off of Highway 17 in San Jose. It was in the early '80's though, but they could custom bend and hang pipe any way you wanted. Welded perfectly - never a rattle or bang underneath, and cheaper than most anyone else.

Something that might make things go easier for you on a self install is stainless band clamps. Summit (and others) has them in our sizes either straight or stepped for joining different size tube. They work great if torqued as specified and can be taken off and put back on as need be, unlike a welded joint. They don't squish or distort the pipes like the usual kind of clamp will.
 
I don't see why the muffler guys should not get paid as much as a mechanic or fabricator. If he/she is really good at what they do, then it is worth it. Bending exhaust pipe is an art. Unless you're willing to piece it together and have plenty of time to do it, I'd say it is well worth it. Just make sure the shop is a reputable shop.
 
Mine was just done similar to what you have - it cost $300 in Flagstaff at Magic Muffler - that included the Flowmaster 50 / y pipe fabrication - everything.....

I was not thrilled with the routing of the pipe - but on a 79 you have few options...

If I had it done again - I would have it routed tighter and then have the Flowmaster mounted crosswise in the back...

Live and learn
 
Back
Top Bottom